Counting matching models…
Taser Dummy with changeable cartridges. i used m5x35 screws and with m5x10x7 Plastc inserts Print Settings Printer Brand: Creality Printer: Ender 3 V2 Supports: Yes Resolution: 0.28 Infill: 10% @ 3 shell, 5 top/bottom Filament: Das…
These are meant to put on the oem rubber feet. not to replace them. If u use the Ender 3 V2 Silent Pack then these (basic_Mobo_PSU_cover_30cm_V1.stl) feet, with this cut out at one of the edges, could be Helpful for you. update updated…
I used this model in my Dartboard Stativ holder Project as a Placeholder. So that i could Plan my Project better.
Nano Vise V2 (by PRIma @ https://www.thingiverse.com/thing:5178901 ). Printed M8 x 10mm Bolt (ISO 4762) (no support needed) source: https://www.fasteners.eu/standards/ISO/4762/ EDIT NEW High tolerance version available…
Simple organizer for threaded dart shafts with standard 2BA threads. can hold up to 15 sets (15 sets* 3 shafts per set = 45 shafts in total ) Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: No Resolution:…
Just a little base for stacking cans in the fridge. The rods have to be glued into to the main part. It is designed for Ø 60mm cans. For example 330-ml-Sleek-Can (0.33L) A detailed Description → TBD
Here is a small minimalistic foregrip for M-LOK rails
The Description will be refined as soon as possible is is just a quick and dirty sideproject.... might be refined soon. some Infos: It's Possible to print withotut Support ~ 3 1/2h print time @.16 layer height Hardware i used:…
will be added soon.... just a quick and (really) dirty side project. Since I currently have little time I would appreciate it very much if someone could clean up the fuison360 files a bit, thanks Print Settings Printer Brand: Creality…
Dimensions Inner diameter: 20mm Outer diameter: 25mm Hole diameter: 3.5mm Print Settings Printer: Creation Ender 3 Rafts: Doesn't Matter Supports: No Resolution: 0.1 - 0.2 Infill: 10 - 20% Post-Printing coming soon. Category: Replacement…
A simple stand for Lithophanes and USB-Lights A detailed Description → TBD
Dart Case — Length Adjustable (V2) A fully adjustable dart case that fits any dart setup — no matter the barrel length, shaft style, or flight type. Instead of being locked into fixed dimensions, this case slides to the exact length you…
Can be used for learning knots like the clove hitch, constrictor and many more. Outer Ø → 14mm Inner Ø and side hole → 6mm .75mm deep knurling Can also be used as a handle to test stopper knots or to tighten knots.
Source code: https://github.com/itCarl/ReflowPlate
Species-appropriate employment and mental challenge for your lil bunnies. How it works it's just a game board with 7 lids: by lifting the lids the rabbit gets his reward. simple, but the rabbits of a good friend of mine really like it.…
Put Magnets in while printing.. No need to Stop the print. This Box is suitable for these forks (~1€ a piece): Aliexpress Shisha Forks The Magnets i used (5 x 1mm) : [Amazon Neodym 100 pieces Ø5mm] (…
Dart COG (Center of Gravity) Finder A printable precision tool to find and measure the balance point of your darts. What it does: Helps you locate the exact center of gravity (COG) on any dart Measures the balance point relative to the…
You need a new Cover when switching from V-Rolls to Linear rail. It's designed to re-use the M3 screws that were installed on the old cover... no extra Hardware needed. You also need this: I used this X Carriage for the Stealthburner:
Currently this Model only works for Voron 0.2 or similiar small printers with 1515 extrusions. ROAB short for R ainbow O n A B udget. The rectangular cutout on the back is for cable management if you only have one RGB port on your MCUs,…
These are all currently available results.
