Counting matching models…
A plain rattan style box. Python sources include parametrization. Drop me a note for models with different dimensions. Several earlier prototypes were printed using PLA with variable layer height settings, either 0.15 mm or 0.2 mm base…
A boring battery stand made to test the idea of a velcro style pattern. The patterns on the side of the stand fit each other, making it possible to connect multiple stands together into larger compositions. Printed with PLA with no…
A magnetic clip for Osprey water hose with 8 mm magnet.
About A tool to help take apart Tassimo capsules for recycling (and maybe get that last bit of the chocolate powder out too :-). Just push the two concentric rings into the hole in the center of the capsule and rotate the arm to cut off…
About A holder to attach the Smart 321 bike light to standard luggage carrier. Holes for two M4 screws spaced 52 mm apart, can be edited in sources. Printing Printed with PETG and supports, no special attention required. Used more…
Printed with PETG for thermal stability, the two halves are glued together with epoxy. The bottom part needs support around the clip, the top part works better with support around sides. Avoid support in the connecting groove. Complete…
Overview These are various bits used to build the Hadley Telescope by Maff on metric hardware. I have started with the Official Metric Remix , which is mostly adjusted for M4 screws and 12 mm rods, and adjusted as needed. Printing…
Stackable box for thread spools. Size should fit Gütermann spools with small reserve for slightly larger variants. Source files permit easy editing of relevant sizes. Printed with PLA with no supports.
A replacement leg for Pfaff Quilt Table. Printed with PETG and variable layer height for accurate thread rendering.
About A simple clip to hang Tassimo capsule packages on a shelf of the Ikea IVAR system. The single sided version is for hanging the packages below a shelf, the double sided version is on the photo. Should fit any shelf with the same…
About Just a simple lid for those large yoghurt cups one can never eat in one go :-) Printing Prototype printed in PLA with 0.2 mm layer height, 2 perimeters, 1 mm minimum shell thickness. Copying Model CC-BY [email protected]. Using…
Replaces the original return inlet to give the water in your pool a gentle spin. Probably also does something when pointed upwards, but I did not try that. The dimensions should be compatible with the common fittings of the Intex or…
An insert for using longer screw with Thule FreeRide roof top bike rack. The rack cannot hold bikes with wide frames such as e-bikes. The insert makes it possible to replace the T shaped screw with a longer M8 screw to hold a slightly…
About An adapter for connecting vaccum hose to hand held Dyson vacuum. Assumes hose with 43 mm outer diameter and counter clock wise thread with 6 mm pitch. No idea if this is in any way standard, it was just the hose I had :-) the thread…
About A flat cover for the center console of Yaris NG Hybrid (tested with 2023 model, might fit others). Our dog enjoys squatting on the center console but sometimes presses the various buttons located there. The cover hides the buttons…
About A tall jar for dog biscuits with slotted bottom for crumbs. We keep dog biscuits in cylindrical jars but over time a mess of crumbs accumulates on the bottom. This jar has a double bottom with a screw-on lid that holds the crumbs.…
About A holder to attach the Bestek Smart Plug power strip to the Ikea IVAR shelf system. Tailor made for Bestek Smart Plug model MRJ6404 purchased from Amazon, held in place with extra screw and washer on each end. Printing Printed with…
Two sizes included, printed with PETG.
Prototype printed with PLA, 1mm top and bottom shells, 5 perimeters, this makes the U shaped part of the holder sturdy enough. Slides onto 17.5mm headboard, dimensions can be adjusted in the source files or just drop me a message with…
I had a prototype printed with PETG but then settled on PLA, both would probably work. For me, 3 perimeters and 0.2 mm constant layer was fine, plus manual color change for the icons, obviously. No supports needed. After printing, rotate…
These are all currently available results.
