P
PrintablesRCWeinstadt
Anycubic Photon Mono tiltet build plate
This is an adapter to tilt the build plate after the print to let trop off uncured resin. The V2 you can find here .
- Downloads
- 550
- Likes
- 61
- Rating
- 4.82
All models
Counting matching models…
P
PrintablesRCWeinstadt
JSN-SR04T ultrasonic distance sensor Holder
5° tiltet holder to correct the tilt of the sensor
- Downloads
- 446
- Likes
- 12
- Rating
- 0
P
PrintablesRCWeinstadt
V2 Anycubic Photon Mono tiltet build plate V2
New version of my tilted build plateholder. This is tilted in two axes. Therefore, the resin drips from one corner instead of one edge. To save some material, i designed some fancy cutouts. Excellent to print on the printer for which it…
- Downloads
- 394
- Likes
- 33
- Rating
- 4.86
P
PrintablesRCWeinstadt
Victron Cerbo DIN rail adapter
You need two of these to mount your Cerbo on a DIN rail. In addition, 4 M4x10 / M4x12 or 4mm sefltapping screws are required
- Downloads
- 391
- Likes
- 25
- Rating
- 5
P
PrintablesRCWeinstadt
Swamp boat
I always wanted to design and print a swamp boat. Now it was time to realize it. The boat consists of two parts, which are screwed together. For sealing the whole thing is glued around the internal cable duct. I took the motor and ESC out…
- Downloads
- 298
- Likes
- 68
- Rating
- 0
P
PrintablesRCWeinstadt
Cabinet knob
You want some functional print in your liveingspace and show your hobby to some other? Here is a little cabinet knob with M6 thread. Print with SLA / DLP printer for good details.
- Downloads
- 266
- Likes
- 59
- Rating
- 5
P
PrintablesRCWeinstadt
V2 Anycubic Photon Mono 4k tiltet build plate V2
New version of my tilted build plateholder. Now for the mono and mono 4k This is tilted in two axes. Therefore, the resin drips from one corner instead of one edge. To save some material, i designed some fancy cutouts. Excellent to print…
- Downloads
- 259
- Likes
- 16
- Rating
- 5
P
PrintablesRCWeinstadt
Two cell 18650 battery holder
Remixed holder for two 18650 cells (user: fns720) with flat ends
- Downloads
- 191
- Likes
- 23
- Rating
- 0
P
PrintablesRCWeinstadt
Devil Heart with ring
Remix of the "Devil Heart !!" from @JohnF_1629456 with a ring attached The harness is obviously not printed ;-b
- Downloads
- 99
- Likes
- 15
- Rating
- 5
P
PrintablesRCWeinstadt
Din rail mount HLK-10M12 PSU
Din rail mount for Hi-Link HLK-10M12 To connect it, I used the 2-pole WAGO 221. These have a port for measuring tips. A wire can be inserted there to make the installation fancy. The wires are then soldert to the PSU Pins. Finally, the…
- Downloads
- 73
- Likes
- 20
- Rating
- 0
P
PrintablesRCWeinstadt
Pi Armor Case mount
For my needs i designed a mount for the Armor Case of my Raspberry Pi 4. With that an 4 screws you can mount the Pi to anything you want. (Unless you can drive a screw into it ;-) Category: Electronics
- Downloads
- 57
- Likes
- 7
- Rating
- 5
P
PrintablesRCWeinstadt
PCB UV Exposure Unit
A UV exposure box is an extremely useful piece to make PCBs. I have searched and found that they are too big and too expensive for my uses. In addition, all the devices require an external power sorce. Thereupon I decided to build one…
- Downloads
- 38
- Likes
- 8
- Rating
- 0
P
PrintablesRCWeinstadt
Lenstube screwdriver for 20mm Co2 lenses
This is a "screwdriver" for the lenstubes of lasercutter /-engraver with a 20mm lens. Print Settings Printer: My own designed Printer Rafts: No Supports: No Resolution: 0,15 Infill: 15% Category: DIY
- Downloads
- 31
- Likes
- 2
- Rating
- 0
P
PrintablesRCWeinstadt
Victron positioning aid for label
I have several Victron devices hanging on one wall. I lasered labels to label them. Since my inner "Monk" likes to have the labels straight and at the same distance from the edge, there is this little helper.
- Downloads
- 30
- Likes
- 6
- Rating
- 0
P
PrintablesRCWeinstadt
GPIO Hackerboard magnet mount
No place to mount the GPIO hackerboard inside or on the Prusa CoreOne? Here is my solution to that problem: You can mount the PCB with two nylon rivets for the CoreOne or with two M3 screws. By stacking three magnets with a diameter of 5…
- Downloads
- 26
- Likes
- 11
- Rating
- 5
P
PrintablesRCWeinstadt
RaspberryPi Din Rail mount
Mounting option for a RaspberryPi to a DIN-rail. I'm using it with a Pi4 with armor case
- Downloads
- 25
- Likes
- 5
- Rating
- 0
P
PrintablesRCWeinstadt
Multicolor switch with WS2812b
The LED switches are great, but the WS2812b makes it even better. So i designed a holder to replace the ordinary LED with a WS2812b. It's a addressable LED, you could dazychain. What's to do? Print the adapter in a neutral color (ore…
- Downloads
- 20
- Likes
- 7
- Rating
- 0
P
PrintablesRCWeinstadt
IKEA TREDANSEN cap
If the side cap of the lower aluminum profile is defective, this is a 1:1 replacement.
- Downloads
- 3
- Likes
- 0
- Rating
- 0
These are all currently available results.