P
PrintablesFierce Pears
Small tractor
Tested with 0.07 layer and supports. Be careful when unlocking wheels, grab both of them and try to twist them.
- Downloads
- 514
- Likes
- 28
- Rating
- 5
All models
Counting matching models…
P
PrintablesFierce Pears
Terraforming Mars Player board
For best result I recommend 1 perimeter and 0.2 layer height with variable height around the text, so after color change there are at least two new layers. Also is good to use slow speed for perimeters to make text sharp.
- Downloads
- 466
- Likes
- 46
- Rating
- 5
P
PrintablesFierce Pears
Nuclear power plant
Printable without supports and with a 0.4 nozzle but result will be definitely better with 0.25 nozzle. Also I recommend 0.07 layer and 10% infill. My power pole also suffered from stringing (mostly because of wet filament and wrong…
- Downloads
- 413
- Likes
- 35
- Rating
- 5
P
PrintablesFierce Pears
Tweezers
Small tweezers for removing poops during print.
- Downloads
- 367
- Likes
- 23
- Rating
- 5
P
PrintablesFierce Pears
Oil well
All parts can be printed with a 0.4mm nozzle. Small parts with 0.1mm layer and rest with 0.2mm. For hammer and crankshaft I recommend supports. The entire model can be assembled without using glue but crankshaft needs some patience, so…
- Downloads
- 215
- Likes
- 36
- Rating
- 5
P
PrintablesFierce Pears
T-Beam Supreme case
Case for T-Beam Supreme, with 18650 battery, which did not require any disassembly and utilize existing screw holes. Printing Everything has pretty standard requirements but logo and buttons should be printed with 0.1mm layer height.…
- Downloads
- 213
- Likes
- 21
- Rating
- 0
P
PrintablesFierce Pears
Eagle keychain / bottle opener
Tested with 0.2mm layer, 70% infill and supports. The back side is little bit messy due to supports, so I added less detailed variation. Overall dimension is 80x27x7.6mm. After first beer there is small scratch in beak but it does not…
- Downloads
- 188
- Likes
- 30
- Rating
- 5
P
PrintablesFierce Pears
Tweezers v2
Slim long tweezers for removing poops during print.
- Downloads
- 151
- Likes
- 10
- Rating
- 4.6
P
PrintablesFierce Pears
Small watering can
Printed with 3 perimeters, 10% infill and it looks like it is watertight. No supports required. EDIT: After some time, a leak did appear after all. I'm adding a version with reinforced walls, which should solve the problem, but I haven't…
- Downloads
- 125
- Likes
- 19
- Rating
- 5
P
PrintablesFierce Pears
Stickman door stop
Printed upside down with supports with only one top solid layer to save some material.
- Downloads
- 119
- Likes
- 33
- Rating
- 0
P
PrintablesFierce Pears
Dino lamp
My version is powered from USB. Bulb is made from 3W LED and 2W 1R5. Hole for switch has 6.6mm diameter. Since I did not used any connectors and everything is soldered together, do not forget to put bulb nut on the cable, before completion.
- Downloads
- 102
- Likes
- 124
- Rating
- 5
P
PrintablesFierce Pears
Small clamp
I recommend printing without IS and 100% infill. Thred has left handed orientation and also you should secure guide and nut with small amount of glue.
- Downloads
- 96
- Likes
- 31
- Rating
- 5
P
PrintablesFierce Pears
Painter's pyramid
Ensure your printing plate is clean and has good adhesion as this model has small contact area. I added version with full base which has higher adhesion. It works better for me while printing multiple pyramids at once.
- Downloads
- 81
- Likes
- 11
- Rating
- 5
P
PrintablesFierce Pears
Spool holder under table
Holder for spools with minimal center hole diameter of 40mm and maximum diameter of 210mm. Mountable under table with screws of 3mm diameter.
- Downloads
- 64
- Likes
- 6
- Rating
- 0
P
PrintablesFierce Pears
Orc bottle opener
Bottle opener with holes for magnets, to be put on the fridge. For the main part of opener I used 3 perimeters and 50% infill, to make it strong eneough. Required parts: Coin with 23mm diameter and 3mm thickness (like 1€). 3x magnets with…
- Downloads
- 38
- Likes
- 8
- Rating
- 0
P
PrintablesFierce Pears
Shrapening angle guide
This guide is intended for sharpening plane irons and chisels. It is designed for 25° and 30° angles. The wheels should be printed with a random seam, and because they are made from plastic, you should expect them to eventually wear out.…
- Downloads
- 34
- Likes
- 9
- Rating
- 0
P
PrintablesFierce Pears
Fields of Green insert
Bowl is printed in Vase mode, do not forget set 0.6 for perimeters to make wall thicker. For Card boxes use for bottom variable layer height and slow speed for small perimeters. Box bottom needs supports in the groove. I made small…
- Downloads
- 31
- Likes
- 0
- Rating
- 0
P
PrintablesFierce Pears
5mm cable clip
Cable clip for 5mm cables mountable with 3mm screw.
- Downloads
- 27
- Likes
- 2
- Rating
- 0
P
PrintablesFierce Pears
Soldering iron cleaner
Inside of body has diameter 48mm. I recommend to print body with 0.15mm layer height and organic supports for best result. You have to use glue to put base and body together.
- Downloads
- 20
- Likes
- 3
- Rating
- 0
P
PrintablesFierce Pears
Fierce Pear
Small bobblehead figure for top of your MINI. Most of the parts printed with 0.1mm layer. Small parts with supports and brim. I printed spear in vase mode with slow speed, so it did not tipped over. Spring has 1 perimeter wall width. In…
- Downloads
- 11
- Likes
- 0
- Rating
- 0
These are all currently available results.