Counting matching models…
Papos98 cable organizer design for hinge with hole spacing appropriate for server rack design by Vincent59. 1-22-21 Untested. Print/use at your own risk. 1-27-21 Print at 0.2 layer height. No supports. Tolerances are on the loose side…
11Lb Spool Adapter for smaller Lincoln Welders. Will probably fit other welders. Category: Tools
Remix of SCX10.2 shock front hoops by justicedspencer This is the V1.0 of shock hoops for the SCX10 2 that allows for near 1:1 motion ratio and scale angle shocks (straight up and down, not angled) and allows for long shock travel while…
This tool is a perfectly snug fit to safely remove fuel filter on a Kubota Loboy Diesel Generator and B8200 Tractor without damaging it. 3D PRINTING SETTINGS 0.15 100% Infill PETG
AMPS mount for Garmin Spine - Remixed from eddiewebbinaro https://www.thingiverse.com/thing:4702949 Print Settings Printer Brand: Prusa Printer: i3 MK3 Rafts: Doesn't Matter Supports: Yes Infill: 100 Filament: PolyMaker PolyMax PC…
Tired of taking the front end of your typhon apart just to dig and search for a single screw that holds the front body post? Just for it to fall off again! This thingi will allow you to thread an M4 Screw from the top. If your body post…
This is an add-on for body post/mounts if you printed my remixed long travel shock mounts/hoops ( https://www.printables.com/model/730892-long-travel-shock-mounts-for-axial-scx10-2 ) These just bolt onto the inside of the shock mount.…
This ball adapter allows you to use the Scosche MagicMount in the iBOLT Arm for Tablets or mobile phones Print Settings Printer Brand: Prusa Printer: i3 MK3 Rafts: No Supports: Yes Resolution: 0.15mm Infill: 100 Filament: Prusa PETG Black…
Note: Version 1 is not perfect, it doesn't extend all the way to the bottom of the intercooler. When I have more time I will make a new version that extends to the bottom and has a 90 degree extension that reduces air loss below the…
This is a mount I made for my car project. It clamps around a bosch electric water pump for a water to air intercooler system for turbocharged or supercharged applications. Bosch pump part# 0392022002 Category: Automotive
This is a rear body post adapter allowing you to run a team associated Reflex 14T Truggy body on your 1:16 mini revo. On the lowest post setting this adapter and and body combo still clears the hot racing sway bar kit (front and rear)…
Hose retainer for dual hose Peristaltic Pump Video: Print Settings Supports: Yes Resolution: .15 Infill: 100% Filament: Generic PETG , PC Category: Tools
This is a mount I made for my car project. It clamps around a reservoir for a water to air intercooler system for turbocharged or supercharged applications. I repurposed a Moroso 85471 Air/Oil Separator Tank to be my water reservoir.…
This mount/stabilizer holds in my Castle Mamba Monster X 8S ESC in my Typhon 6S V5. I have secured the bottom of the ESC with Genuine 3B VHB which helps with shock/vibration isolation (as well as the stabilizer being constructed of…
Instead of drilling a hole to mount the apexus fuel transfer switch/gauge I decided I wanted to use the standard phone AMPS mount interface. Category: Automotive
This adapter cover allows you to use a ball bearing instead of the unserviceable bushing that wears and has no replacement (must purchase entire pump, not just cover) It is designed to hold this bearing:…
Just uploading g-code for Polymaker Fiberon PA12-10CF
These are all currently available results.
