Counting matching models…
This clips on to the fence and holds the wire away. I made it as a stop gap measure until I can reset the fence line. This is a cheap and easy solution for now. My fence has 6.19" (1.57226 Decimeters) spacing between the horizontal wires.…
This is V5 of a prosthetic leg for a chicken who has lost her foot in due to frostbite. Otherwise a healthy hen. It is very much not refined and needs a lot of work. I plan on adding better versions in the future. I'm including previous…
This is a working project. This insulator should be able to clip on to a fence in multiple different orientations. I'm still working on it and it isn't perfect. But it is functional. Probably should use PETG or another UV resistant…
I made this power brick mount so I could stick the brick to the back of my TV but still be able to remove it to take it to other places. The back of it is smooth so one can use command strips to stick to flat surfaces. Works great for me!…
I broke the wheel on my trailer dolly by moving it sideways on gravel with the tractor. Harbor Freight doesn't sell replacement wheels and I didn't want to buy a whole new trailer jack. I've not fully tested this yet. I'll update this…
Do you have an inflatable hot tub and wished you had a dry armrest to set things like phones and drinks on? Look no further. This shelf sits right over the edge and is easy to remove when putting the top back on. It has drain holes that…
Basic wall mount, use command strips or screws to attach it to the wall. Category: Other
I had some 1 gallon glass carboys sitting in my basement that were getting dust on the inside of the glass. So I made and printed these TPU caps to close them off from spider and dust. Works great. Slides right on and easy to pop off. I…
I've gone through a few different versions trying to get a gasket that will properly seal the hose end and the quick connect end. This is by far not perfect. But it does seal using 95a Overture TPU. I will probably revise this design in…
Do you have old Unifi AP-LR access points that you’d still like to mount and use? This mount is designed to either be screwed in or to be zip tied. I’ve only used the screwed in portion so far.
The cheap aluminum bracket for the storm door to my garage broke, so made a new one. It has been working for the last week or so no problems.
We are planning on installing a cat walk in our toddler's room to help give the cat a safe vantage point from a roving toddler. We also needed a bracket to hold our black out curtain rod the right distance from the window.
This is a simple Wall mount for a Seagate Backup Plus Desktop Drive. Mine is a model SRD00F2, I don't know if it will fit other models or not.
This is a top hat style potty that I made for using with my daughter shortly after she was born. My wife and I were planning on doing elimination communication (EC) with her. We used this potty maybe once or twice. We ended up finding it…
Super basic wall mount for a Belkin USB Hub F5U237. It works, it isn't perfect but it is an early design of mine. Category: Other
Needed a quick simple wall mount for my Harbor Freight Power Bar. Should work for any power strip/bar that is 1.5” (38.1mm) wide and 1.19” (30.2mm) tall.
I made this nutcracker nut shaped. Probably not the optimal shape for it. But it does work. I've included a longer handle that I've not yet tried out. The short one isn't too comfortable after a while. I found that I couldn't use normal…
A coworkers air vent had broken in his 2023 Toyota Tacoma 2023 TDR offroad truck. This seemed to be the hole diameter and length that caused the vent to open and close correctly. I've included the freecad file if you need to make changes…
This is a replacement seat bracket compatible with Ryobi 42" 80v riding mowers. I've not had a chance to test it beyond sitting on it and trashing around. I'll report back after a mowing season. The print quality doesn't look great…
Need two pegboards holes to match up regardless of the distance from the edge of the sheet? Try this! I sized it for 3/16" hole 1" inch spacing pegboard from Home Depot. I printed 2. One for each edge as I was installing it. They fit…
Is your Donvier Chillfast Ice Cream Maker handle broken? My in-laws was, so I made this. I unfortunately don’t have a picture of it on the Ice cream maker, but i’m told it works great. It is made from 3 parts and requires a bolt under…
My Daughter was gifted this Jupiter Workshops Supermarket play center . But the scanner was missing the battery door. Whenever she’d play with it for a few minutes the batteries would fall down enough to make it stop working. At which…
Wife bought a Parent's Choice 5" Round Silicone Bowl with Lid and Suction Cup and wanted a way to mount it inside the cabinet door since it doesn't stack with our other dishes. Whipped this up. Not a work of art but it works and is hidden…
Simple wall mount to hold the HDHomeRun Connect Duo. That's all.
I needed to compression test my John Deere 955 tractor but my compression kit only had ones that thread into the injector hole. The 955 uses a Yanmar 3TN84RJ which doesn’t have any threads on the injector. It relies on a metal bracket…
https://schylling.com/product/metal-speedster-fire/ Have you lost the ladder, determined that it looks like your kid could fall on those metal brackets, or need more cargo capacity? Look no further, simply print a basket to replace the…
I got this no-name-brand bell waterer which works great except that the shaft that it hangs from is not UV stabled and broke after a year. I made this replacement shaft in two parts. Hopefully this helps fix someone else’s waterer! Prints…
These are all currently available results.
