Counting matching models…
I like the original design, but it seams it is designed for left handed. My right hand is reserved for the soldering iron. So, the files are mirrored, to be used with left hand. It sits better in left hand, and scroll cog does not poke…
Desktop stand for multiple DIN rails and configurations. Holes are designed for M3 screws.
I did not like few solar cable clips that I have tried, so I have designed my own that sits snug, clips over the panel edge, and hides the cable under the solar panel frame. It fits perfectly with HYUNDAI HIE-S440HG G12 which has 1.2mm…
Printed out of PETG, 0.2mm layer height. Clicks in it's place over the busbar and sits snug. It has small slot at the both sides for the balancing wire. Designed using busbars that came with my batteries from nkon.nl.
You need to print 2 pieces in order to mount it to the DIN rail clip. I have printed it out of PETG. Screws are ⌀2mm. I like to use it with this DIN rail clip (bit modified version is included in the list):…
Although the air vent I am using has slats that should be enough to stop the rain entering my camping truck, somehow it is not enough, so I have designed this cover. Pay attention not to apply the glue to the draining slot, so eventual…
Good quality busbars can be quite expensive, and most of them are of bad quality or completely unsafe. I made this one of a 20mm wide, 3mm thick copper flat bar, but you could go thicker if you have a need for it. Mine is for summing 2…
Terminal cover for double screw terminal Eve LiFePO4 prismatic cells (LF304, LF280K). I printed it out of PETG with 0.2mm layer height. Fits snuggly. Pay attention not to press too hard on the overhanging part of the aluminum terminal as…
Screw on panel mount adapter for the high current DC connector (female QS8). The connector is epoxied to it. It is printed out of PETG.
Precise and robust bracket for Parkside battery charger (model: PLG 20 C1) that allows to be mount/dismount at will. No support needed. Best to be printed out of the PETG Adjust the M4x10mm screw to grab the charger snuggly and once you…
I wanted under desk mount for my Motu M2 audio interface. There are quite a few designs around, but most of them are not very precisely measured, so I designed my own. I have made it 30° to be more ergonomic, and the meters can be seen…
Not much to say. Standard (at least in Europe) 35mm attachment.
This RPi 4B and SSD mount is designed to be as compact as possible. I wanted to use it with standard commercial brackets as I find them to be bit better strength and elasticity compared to the 3D printed ones. Everything is printed out of…
I have made this vase following this Solidworks youtube tutorial: https://www.youtube.com/watch?v=GVW1zkMf8T8 NOTE: It should be printed in vase mode.
I needed a solution to secure Raspberry Pi USB power cable to the DIN rail in my truck. I am powering RPi4 from the truck's 24V leisure battery trough the USB C port to have additional protection which you don't have if you power it…
Original Eve busbar for LF304
Housing for the 600W DC-DC Boost Converter. There are a few different versions. Take a look at included photo for comparison. LED should be bended 90°, so it points at the side. Small adjustment holes have guides so screwdriver hits…
I am often taking my external hard drive with me, and I didnt have a proper, safe place to put it while it is hooked to my PC. This mount is designed bigger to accommodate 3mm thick felt padding that is glued to the bottom, and to the…
I was surprised by how overpriced and ugly the desktop speaker stands were online, so I decided to do something about it. I made a super affordable stand using 3D printing and concrete – in a way tha I haven’t seen anyone else do before.…
This is practically the same model as my Triple DC Busbar just with added spacer insert to allow it to be used as fuse block. If you drill the holes accurately and you gonna use just one cubeOTO/MRBF fuse, than spacer insert is not…
These DollaTek GPIO boards from Amazon are cheap and practical, but 2 mounting holes are completely useless. My solution is mounting it to the sub-plate with 2 clips. It holds the board very well.
Raised conteoller sides so keyboard fits under it. At the end I have decided to use it as a routing template, and make the sides out of the Multiplex. Not real wood, but still looks better than printed version.
Printed out of PETG with 0.2mm layer height. DIN clip is on one side so it can be printed without support, and it is plenty strong. I have modified original clip design to suit my needs. Electrodacus website: https://electrodacus.com/…
I have tried various DIN clips, but I still like the most common injection molded ones. This DSSR20 mounting plate is for the common DIN rail clips with 12.5mm spacing. You will need two M3x12mm countersunk screw with nuts. I used 2 nylon…
Electrodacus DEXT16 DIN rail mounting plate. I have used common DIN mounting clips with 25mm screw spacing from Amazon, as I find those much better than all the 3D printed designs I have tried. Electrodacus website: https://electrodacus.com
These are all currently available results.
