Counting matching models…
i fixed the ears. the original stl ears holes i were messed up. and i smoothed it. https://skfb.ly/69POn Print Settings Printer: mp select mini Rafts: Yes Supports: Yes Infill: 30% Notes: i printed with kitty on its back. raft and…
snoopy see 3d view here: https://skfb.ly/6v7tp Category: Sculptures
chip clip v3 Category: Household Supplies
a Tinkerbell sculpt. print no less than original (which is in inches) or will lose fingers. fingers are very fragile. take great care. can be printed smaller if using a resin printer. use supports. Category: Sculptures
this is a batman i found on the web. thot u might like to print it. inches. Category: Sculptures
just a cute unicorn. i thickened around the area where the tail connects to the body so the tail is less likely to break off added a even thicker tail section to make it less breakable at that area. Category: Sculptures
unicorn cookie cutters i added one that has chamfer at top for better cutting. Category: Kitchen & Dining
a remix of Keychain: Minion Loves 3D Magic Makers by 3DMagicMakers. Category: Sculptures
another chip/bag clip. 3 widths. .38 in., .5 in., .75 in. and step to make your own width or whatever. no supports. Category: Kitchen & Dining
a hollow, baby groot with a open mouth smile. Category: Sculptures
i based this from youtube design. https://www.youtube.com/watch?v=JMbT4DOi21U the cap that holds the blade in also snaps closed to keep cap on securely. i made slots for the blade in 1/8 increments, ranging from 1/8 to 1 inch. i included…
i made this baby groot hollow to use less filament. it looks printable with no supports and 0% infill use supports only at the back door which holds the led. with no infill but with 3 inner and outer and top shells. Print Settings Rafts:…
baby groot without the base. see 3d view with music here: https://skfb.ly/6uzpK Category: Sculptures
i made this version to take less time to print. so i shortened it and slotted the bottom out. use supports as in my picture. added a step file. added a closer fitting lid with gripping area. added a bottom file. the added lid and bottom…
a nice dome made of hexagons. Category: Buildings & Structures
i remixed the design of COIN SORTER 100% PRINTABLE. EURO by neoprenox so that it would be easier to print and assemble and use less filament. and also to make the cranking so it dont need gears. i added a ramp with a cover to keep coins…
this is a remix of https://www.myminifactory.com/object/3d-print-beauty-and-the-beast-belle-23915 printed with 0 infill, 2 top and bottom and 3 outside layers. uses very tiny amount of supports. Category: Sculptures
a different version of my chip clip and is thinner than my original chip. this is in inches so you need to convert to mm. Category: Kitchen & Dining
my attempt at a batman bust v2 Category: People
a lazy susan to put spices, vitamins, or whatever... i fixed the roller pin problem. Category: Organization
baby groot with both arms up. Category: Sculptures
baby groot standing w base. view with music here: https://skfb.ly/6uzr6 Custom Section Category: Sculptures
pocoyo i made it hollow to save filament. use supports. i fixed the empty spaces issue. Category: People
this toothpaste cap has holes so that toothpaste squeezes through to put on toothbrush. u will have to remove a lil bit of supports up near the nostrils on the inside. i used a drillbit and wire to loosen it and pushed it back and out and…
this is a print in place chip clip that locks via a ratchet type clasp. it has a indent in the middle to hold the bags better i included a step file so you can make it any length you want in the software of your choice. the file is in…
i tried to brake it down into its basic components so they could be printed easily. just print and assemble the pieces. this could be used for shredding kitchen food to add to compost bin. which is why i made it. or shredding veggies for…
this is another version in which i rounded it. i enlarged the spacing to make it easier to slide bags into it. it is bout 10 inches long. for large bags. but easy to convert to any size. no supports. Custom Section Category: Kitchen &…
i made this for my stand that has a glass door that came with a magnet latch that broke. its a simple snap latch that i will use strong double sided tape to adhere to the glass door ad top. many uses. doors, cabinets, drawers, windows,...…
i remixed this to fix the problem with the printing of the upper parts that need support to keep from sagging and stringing.and bending etc. the supports/braces are meant to be be broken off after printing. but only the middle one need to…
this golds 9 guitar picks. it is easy to put picks in and remove. use supports as in my included gcode
i adjusted my standing model to sit and i made .adjustments. see in color and 3d view here: https://skfb.ly/6uL8B i oriented it right. and flattented the bottom to print easier Category: Sculptures
a model of young anna Category: People
remixed a nice looking flower by hex17, into a stove knob. Category: Kitchen & Dining
my design for a sanding block. uses a camming lock to hold the sandpaper.
hello kitty stove knob a smoothed version. Category: Kitchen & Dining
minion loves mom view in full color 3d here: https://skfb.ly/6uL9H Category: Sculptures
chili pepper cookie cutter Category: Food & Drink
this has rounded ramp for cotton swabs, needs supports. Category: Containers
a simple lazy susan design simply place rollers into slots in bottom and the top place top on rollers . this is an improved version. no supports
a dragon attacking on a holder base. the dragon can rotate on base or be glued in position. i thickened the wings for easier printing. Category: Sculptures
this is a toothbrush cover for the electric oral-b toothbrush. it snap securely onto toothbrush. it has a funneling opening to guide the brisles into the cover . no supports. Category: Bathroom
i remixed this to hold scissors and a squeegee and more tools and changed the cutter tool holders to a simpler design lessening the amount of filament and time to print and also they need no supports. i added a cameo logo holder and a…
i made this per request so there is no need for supports. there are 2 files. 1 is solid (per user infill) and the other is hollow. Category: Sculptures
this is an easy to use and easy to print belt buckle. no supports. Category: Accessories
another toothpaste dispenser cap. this one of the elsa character. Category: Bathroom
pull up top knob to bring up qtips to take them out. i included a step file o make it easy to modify. no supports
i remixed this to fit any size marker to use with airbrush. i obviously made cosmetic changes too. screw may be very tight but should get it in with some effort. else use 3/8-16 screw or tap. to use, put in marker and tighten with screw.…
a wind powered bubble machine. for table or bike. or moped?. or car? Category: Mechanical Toys
a trap for air soft bbs and whatever. target rocks when struck. ez assembly. included . has 2 small targets and 1 bigger one. or you can tape your own paper target on the front. Category: Mechanical Toys
this uses a screw plug to plug the shaker. Category: Kitchen & Dining
this jagkommando knife PROP, is printed in pieces for better printing. there is a screw that screws into the blade and the handle to hold it together. i also threaded the butt to screw into the handle. and the handle is hollow so you can…
i made this as a minimal hdd stackable system. the slots in the side allow for you to secure these with screws to the hdds. it has dovetails to keep it from lifting up if you dont use screws. these are not secured to the case in anyway.…
qtip holder round lift up to refill Category: Containers
this is a print in place design. use support and raft. u will have to break the shafts free of the box with a little twisting back and forth. then your good to go. i have cut flats on the shaft at the places where it needs freeing, cuz…
this work by ratcheting as you tighten up the tube (by turning the knob) i used supports, of where there is only i tiny bit. after assembly work in the ratcheting part because there is a little bit of support under the ratcheting levers.…
baby groot salt and pepper shaker. it has a plug that fits into a hole in the bottom of the left foot which is where you put the salt or pepper , or herbs. edit: i straighted it out to be balanced. Category: Food & Drink
inspired by octo kinetic sculpture. isin inches so convert to mm if u dont have simplify3d. supports needed only on the 8, s shaped cups. by Anthony Howe checkP; https://www.youtube.com/watch?v=PIbk4AKFMTc i changed the ring to fit to the…
a complete geodesic dome. print as in picture so no supports or raft. but i used a brim with 1 skirt layer and 5 skirl outlines. to help keep it stable. it dont think i even needed a skirt/brim. it just looked so vulnerable. i used 10%…
this PROP gun shows theoretically, the gas forces the slide back against the slide return spring. remove the barrel by moving the slide back enough to move the barrel back abit to move barrel back and then up and out. . put a bullet in by…
this holds 31 micro sd cards and 3 sd cards. or any combination thereof. Category: Computer
remix of Microtech Jagdkommando by Nikola Svilar: https://grabcad.com/library/microtech-jagdkommando-2 all i did was make it so that the blade and handle can be printed in separate pieces and the screwed together with a screw. the rest…
superman holding rocket. included separate files for rocket and superman . . with separate files you will need to glue, epoxy, whatever superman to the rocket.. Category: People
i remixed this to be able to print in 2 pieces without supports. and i made the top slidable imstead of using threads. Category: Outdoor & Garden
this dispenser holds aprx 65 aa batteries. so the two hold 130, three holds 195 batteries., etc., etc. you can stack them side be side. its appx. 8 in. tall. is in inches. use supports. Category: Electronics
toilet paper holder. you just place full roll on shaft. when its empty just remove from shaft. Category: Bathroom
this are lite/compact versions of my remix silhouette-cricut tool holder : http://www.thingiverse.com/thing:3753555 this is a lattice design to lighten it up further. costing half as much to print as a solid one. no supports needed…
insert the food in the feeder tube push down with feeder and crank the handle. food comes out bottom. i hav included 2 types of crusher gears. the first type are the same so only need to make two. but second type u need to make 3 ea of…
batman vs superman logo for keychain or earings Category: Accessories
i changed the spring design of the original into a compliant sprint. it seems to work much better. the original spring didnt have quite enough umph which is why he made a stronger spring but the stronger spring was doesnt work. so i made…
a filament spool holder for the creality cr 10 that slides along the top aluminum extrusion. print on its side so no need supports. needs supports. Category: 3D Printer Accessories
there are 2 versions . the dragon fountain head that goes on a water pump extension tube that is .58 inch diameter. water goes up and out the mouths dragons. Category: Outdoor & Garden
these hubs can let you construct a geodesic dome with 1/2 inch rod such as pvc or wood etc. for the struts. this works because the hubs will bend allowing the end to match up. with the 3p hubs you will only need 1 size strut. with the 5p…
i remixed this so i could print the tong s in plastic. and so i could change the tong to any type i want. i included step files so u can modify it to your liking. i printed my tongs with fast honeycomb internal infill pattern, at 20%…
i made this chip clip with a funnel lip entrance, to guide the bag on the clip better. no supports best if you can print this without brim. if you use brim u will have to remove it from along the inside area. Category: Kitchen & Dining
this is a i think better redesign of my other ratcheting design. you just slide end of tube into slot in roller and wind. an arrow on rod shows direction to wind. the ratchet design will hold tube from unwinding as the tube rests against…
wonder woman cookie cutter Category: Food & Drink
hinged box with snap locking tab. this can be modified to be deeper. or wider. i included a step file for easier modifications.
see it here. https://youtu.be/P2Itm0LUR1k a gun prop design based on the desig by mark sebu, the gb22. this gun has 2 parts and no weld or screws etc. the barrel fits into its place , then the slide just fits into the frame uses rubber…
i redesigned this to see if i could remove the supports that simplify3d said it needed. it still wants to add a cpl supports but i printed it without supports and it works just fine. it needs no supports Category: Toys & Games
this wind bubbler has the wands incorporated into the fan blades. size is approx 162mm which is a lil over 6 inches. i added a bubble solution auto filler adapter to help keep solution reservoir filled via a soda bottle that screws into…
a cookie cutter that impresses the face of moana anmd cuts out the round outside cookie shape. Category: Food & Drink
this is to carry frozen fish food balls from the freezer to the fish tank and dropping it in. cuz i hate grabbing it with my hands . *beefed it up a bit. Category: Pets
this is a print in place one piece print, to clamp around a round rod .876 inches in diameter. but it can be used for square posts too. im showing it as is to show the concept. i will add a holder for stuff then clamp it to my desk which…
agnes from despicable me in tutu. Category: Sculptures
i made here a lucida frame that need a glass for the front and a mirror for the back. it has a go pro connection for a go pro tripod attachment. Category: 2D Art
another dragon fountain. Category: Outdoor & Garden
this has got to be the toothpaste squeezer ever (or so far). this is a toothpaste squeezer with spring return ratcheting mechanism, and a tube release mechanism. you just press to roll up tube and the return springs return it to ready…
batman vs superman bubble wands Category: Accessories
a cpl of dragon fountains with a bell fountain top. one top piece is included cuz both fountains use the same top piece. Category: Outdoor & Garden
a more simple (i think) remix : https://www.thingiverse.com/thing:3469633 of a corner brace system for 1 inch square tubing. i uploaded one with sharp corners. Category: 3D Printer Accessories
i remixed this to make it even better. i made it wider i made the spring separate so it could be modified and replaced easy. and i made the base 1mm shallower so it would provide more spring distance. the original was harder to wind all…
a print in place chip clip with a camming clamp to hoild the bag. Category: Household Supplies
