Counting matching models…
Replaces stock barrel coupler and muzzle. Install by simply dropping into the blaster once the stock muzzle and barrel coupler has been removed. Intended to work with stock barrel only. This modification removes all indexing issues…
Modified pusher to clear flywheel cages with dart guides. Used in conjunction with Talon compatible cages by ahalekelly ( https://www.thingiverse.com/thing:2843287 ) Feeds perfectly using Worker Talon Adapters designed for flywheel…
Picatinny sling point for all your Nerf / blaster needs. Requires one M3 bolt and M3 nut (I use a nylon lock nut).
Requires only 3 (EA) M3 nuts and bolts. Also optionally requires a small amount of super glue. Print in orientation as imported into slicer, with supports touching build plate enabled. Adjustable rear sight is assembled in the same…
Lower fill for Nerf Stryfe featuring standard picatinny rail. Tight fitment, and also includes a hole for one coarse thread M3 screw. New version requires both “M3” parts and is installed by replacing the N-strike accessory attachment…
Adds a bit of elevation to the Outlaw rear sight for better and more intuitive blasting. Print as imported, support 90 degree overhangs. Block supports at the holes. Install dots by applying superglue to 1.75mm filament, pressing in, and…
Thumb screw remixed to work with the Quik Blaster's extended battery tray by OldFusionDesigns. Requires 1 (EA) M3 bolt and 1 (EA) nylon lock nut. Print orientation as imported. Enable support touching build plate (optional).
Shell: Converts the Nerf Sledgefire to fire 1 half-length dart through a 17/32 brass barrel. Deactivates the air restrictors well enough without needing removal. The brass barrel must be epoxied into place inside the printed shell. I also…
Stamp to aid with cutting 1/16 Inch (.0625”) thick adhesive backed foam. Improves seal as required for many Sledgefire upgrades! Print as imported, no supports required. Place stamp on a piece of 1/16 Inch (.0625”) thick adhesive backed…
Popular muzzle remixed for use with the Worker Retaliator POM short dart drop-in kit. Requires no additional hardware. Notes: Fits any barrel <16.2mm OD. Friction fits, elephant's foot will require post processing where barrel mates with…
Another (Mega)Jolt reskin. Remixed to be a simple single-shot muzzle loader. Drop-in reskin/rebarrel for Mega BigShock. File set includes a spring spacer, barrel, and remixed shell. Works without removing the air restrictor(AR) and is…
Un-pump grip your pump grip SPAMF. Installs using existing hardware. Print as imported, no supports needed. Optionally add two strips of grip tape for more grip!
12mm and 20mm 3m through bolt standoffs for use in the SPAMF. Two of each is required. Sand to fit as needed. Recommended to print all 4 upright on a raft simultaneously.
Print in orientation as imported; enable supports touching the build plate. Attach two parts with epoxy/super glue. Print is designed to mate with this magnet . Requires MagSafe case. Works with stock Type-C to Type-C cable.
Muzzle parts are intended to minimize the blaster, as well as remove cartoonesque design elements. Other parts included make for a fun flywheel mod project! Refer to a Stryfe wiring diagram as needed if installing hobbyist components.…
Adapter to add your favorite sight to a Nerf Retaliator barrel. Print in orientation as imported with supports enabled everywhere. Requires (1) M3 x 12 bolt as well as (1) M3 nylon nut. Open the shell of the Retaliator barrel. Replace…
A top picatinny rail and a remixed 7-dart spinner for Palmtopper's Bustershot. The rail has great fitment, but I have also included two holes for M3 coarse thread pan head screws (optional). The spinner was redesigned because I…
Print as imported into slicer program with supports. It is also recommended to block supports at all holes; only the picatinny rail, “Rear sling point”, and “Front Align with Sling Point” require supports. Recommended to print with 4-5…
Intent: Slightly extend barrel for a Nerf Retaliator sleeper build. All parts of build fit into a Nerf Retaliator barrel. The parts used in this build are as follows: 40mm length 13mm ID KuryKafe barrel Worker scar-like barrel attachment…
A quick remix of the following model: https://www.thingiverse.com/thing:3868513. Full credit goes to the original creator! Removed watermark and increased the thickness of the model's thin wall. Install with M3 bolt cut to appropriate size.
Replacement rear sight, fits Aeon Pro. Adds elevation adjustment for better blasting! Print in orientation as imported. Enable supports everywhere; block supports at the holes. Install dots by applying superglue to 1.75mm filament,…
Adds both a crude sight and a bit more grip area to top prime your higher spring load Retaliator. (tested using 7kg Worker Spring) Inspired by a similar model found here (borrowed some of the geometry) and refined the design. This top…
A two-sided picatinny rail for attaching attachments to attachments. Attach a grip to the Proud Papa platform!
Housing to seat 17/32 brass barrel, fits Nerf Firestrike. Used in conjunction with mnorton95's venturi . Intended for sleeper builds with shorter barrels. Print as imported with supports enabled touching the build plate. Simply orient and…
Print as imported - friction fit installation. Surge protector will require two covers. Intended to cover keyhole slots on bottom panel when not wall mounted.
These are all currently available results.
