Counting matching models…
Updates updated rails to be .5mm shorter for gridfinity and for tighter magnet fitting 24.6mm and 2.8mm deep. added V-style holder for ratchets and large extensions 8/17/2024 3-4 inch drive tool and socket holder and washers 2/18/2024…
I couldn’t find a Gridfinity wrench organizer that fit my needs, so I used OpenSCAD to dynamically generate this wrench holder with customizable labels. Follow the steps below to set up OpenSCAD and create your own. I’ve included many…
Modular Bathroom Organizer, my eureka moment in the ongoing battle against bathroom counter anarchy! Born from the depths of clutter-induced despair, this 3D-printed marvel is a testament to order and harmony. Its genius lies in its…
cheap, low filament, low complexity organizer for gridfinity system. Wedges can be used for pliers and square-shaped things.adapted from Zack Freedmans gridifinty system. A lot of my plies would take up one and half grids and appalled by…
openscad file to generate simple clamps you can delete the fillets if you want. Just spec your dimensions at the top and your good to go! Category: Tool Holders & Boxes
3d model for a jeep yj dash. Dimensions are not exact but should be close enough. Left gauges blank so you can add your own custom layout. Print Settings Printer: creality k1 Rafts: Doesn't Matter Supports: Yes Resolution: 2.00mm Infill:…
Lc coupler the tolerances may be off a little. Printer will need to be dialed in to print this. used .1mm and printed with petg and pla. try printing on end with supports on curve. do not add any supports in the holes or else it would…
I made this openscad program to easily generate a simple case for little electronic boards. You can import it into whatever application you want cut your holes for certain boards. The holes are auto positioned to be in the center of the…
10 spline .75 pilot bearing clutch alignement tool. Printed with 6 walls and 25% infill just for durability. Should work with most jeeps apecifically used for ax15 installation in my wrangler. May fit other jeep clutches or situation like…
I printed this out of PLA. I had chat gpt generate an openscad file based on the properties of a dayton 8ohm full range 4" speaker. I shelled it out and filled it with sand and mortar mix and sealed it with liquid nails. I added a veneer.…
link to relay https://www.amazon.com/gp/product/B07WQH63FB/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&th=1 generated using the KISS openscad case generator https://www.thingiverse.com/thing:6303474 Category: Electronics
I had trouble aligning my timing chain cover to align perfectly with the crankshaft. Loosely mounted timing chain cover and slipped this over the crankshaft snout. It is a very snug fit for limited play. I also used it to help drive my…
Instead of making it round made a square top so it can be printed on its side easier. Printed with 4 walls and 25% infill. Printed with ASA. I printed vertically but it ended up snapping along the threads requiring a horizontal print for…
Printed at 40% infill using polycarbonate wheels at 40% TPU print wheel blocks on side with supports. bump stop gets printed with notch facing up. To assemble, remove whole rear cover. Pins will need to be pressed out to remove old…
This verision extends out to provide as a drill jig for an 11mm drill as well. original model was fine for marking but wanted to just use it as a drill guide as well when clamped. printed with 4 walls for extra strength. Include cherokee…
Used to mount an6 lines on frame, firewall and in engine bay. Recommend using pet-g and durable. I used polycarbonate.
Made this to slide over the input shaft on an ax15. 10 spline .75in pilot bearing. Used a hex size bolt sticking through end to hook my drill to. Handy to test used tranmsission before installing or when buying used.
Could not find a tool that worked for my 1987 jeep wrangler to prevent proportioning valve from tripping while bleeding troublesome brakes. Only way i was able to reset it was to disconnect the brake lines and physically push it back with…
I designed to adapt a harbor freight 36 inch toolbox with softclose drawers to use leveling casters. this makes a great 3d printing toolbox that is completely level and fits over 20 rolls of filament perfectly in the bottom drawer and…
These are all currently available results.
