LayersFactory

All models

Sort order

Counting matching models…

P
PrintablesLeavingthelegacy

Under dash AEM Air/Fuel gauge pod with 3 degree angle

Use PETG or ASA. Holes are made for M3 threaded inserts.

Downloads
144
Likes
12
Rating
0
Order a print of this model
P
PrintablesLeavingthelegacy

Tennessee Vols coasters and holder for MMU

Merge the inner and outer in your slicer. I printed the holder on my FLSUN V400 to save some time. Made for 7 coasters but could easily be adjusted for any amount. Let me know if you want a different number.

Downloads
109
Likes
27
Rating
0
Order a print of this model
P
PrintablesLeavingthelegacy

Skimmer Guard for above ground pool with SunSolar Through Wall Skimmer

Everything that floats in our above ground pool would work its way into the skimmer so I created. Printed in white PCTG

Downloads
89
Likes
10
Rating
5
Order a print of this model
P
PrintablesLeavingthelegacy

12 volt/USB plug adapter

Screw holes are 5mm. Adapter hole is 30mm. Print in PETG or something that will stand up to the heat of a vehicle.

Downloads
36
Likes
9
Rating
5
Order a print of this model
P
PrintablesLeavingthelegacy

Tesla Model Y headrest bushings

After installing https://www.printables.com/model/251256-tesla-model-y-rear-seatbelt-guide one of the headrest started squeaking so I made these. I don't like having the headrests down all the way due the seat release being covered by the…

Downloads
22
Likes
4
Rating
0
Order a print of this model
P
PrintablesLeavingthelegacy

Trunk or treat winner base for Bobblehead Jack-o'-lanterns by 3DPRINTY

Trunk or treat winner base for Bobblehead Jack-o'-lanterns by 3DPRINTY. I should have used ironing for the top layer.

Downloads
18
Likes
1
Rating
0
Order a print of this model
P
PrintablesLeavingthelegacy

Hydrojug handle pin

When my daughter used the handle to open the bottle she lost one of the pins that holds it in place. Printed in PCCF, then glued it in the hole with the handle in place. MAKE SURE YOU DON'T GET GLUE ON THE HANDLE. If you plan to put it in…

Downloads
17
Likes
1
Rating
0
Order a print of this model
P
PrintablesLeavingthelegacy

Tesla logo added to trash can lid and fixed the problem with the can falling over/sliding.

Added the Tesla logo to the lid. Printed with Prusa XL using PCTG/PETG I have the all weather floor mats in my car so the spiked feet didn't hold very well. I added magnets to the base and put a piece of sheet metal under the floor mat…

Downloads
15
Likes
5
Rating
0
Order a print of this model
P
PrintablesLeavingthelegacy

1933 Jeep Willys Ignition Switch Holder

Hole in dash was too large for new ignition switch. Black PCTG

Downloads
15
Likes
4
Rating
0
Order a print of this model
P
PrintablesLeavingthelegacy

Prusa XL multi-material layer shift test

I used TPU in TH3 for the legs, PETG in TH2 for the supports, PLA in TH1, TH4, and TH5. This took about 17 hours and over 2000 TH changes I should have dried the TPU for another 24 hours

Downloads
14
Likes
1
Rating
0
Order a print of this model
P
PrintablesLeavingthelegacy

Purse holder for late model Chevy Tahoe

Will continue to innovate this. Might put a bar in between the two holders

Downloads
13
Likes
2
Rating
0
Order a print of this model
P
PrintablesLeavingthelegacy

Lulzbot TAZ6 eBOX dryer stand

Wanted to place my eBOX dryer on top of the frame. Simple but effective.

Downloads
13
Likes
2
Rating
0
Order a print of this model
P
PrintablesLeavingthelegacy

1933 Jeep Willys Dash Light Switch

I used a soldiering iron to heat each terminal up to 250C then pressed them in. Also used a little bit of super glue to make sure they wouldn't loosen up.

Downloads
12
Likes
2
Rating
0
Order a print of this model
P
PrintablesLeavingthelegacy

40mm cubicle coat/bag hook with anti-slip

Simple but strong coat/bag hook for a 40mm wide cubicle. The hook is PETG and the anti-slip is TPU. Took about 45 minutes total.

Downloads
11
Likes
3
Rating
0
Order a print of this model
P
PrintablesLeavingthelegacy

1933 Willys Jeep headlight adapter

A friend is re-building a 1933 Willys Jeep and asked me to design and print a headlight adapter. I used white PCTG

Downloads
11
Likes
2
Rating
0
Order a print of this model
P
PrintablesLeavingthelegacy

AC vent with rocker switches

Added an aftermarket AC system to a 1968 Mustang. Needed to mount the vents and rocker switches. Printed on Prusa XL with 2 colors. You will want to print face down for the writing to work.

Downloads
10
Likes
2
Rating
0
Order a print of this model
P
PrintablesLeavingthelegacy

Magnetic skimmer cover for SunSolar Through Wall Skimmer Kit

*YOU MUST PUT MAGNETS IN THE BACK OF THE SKIMMER* You can see in the pictures what I mean I am tired of pool equipment getting stuck in the skimmer. If you have an above ground pool and you added an in wall skimmer you need this. Make…

Downloads
10
Likes
4
Rating
0
Order a print of this model
P
PrintablesLeavingthelegacy

Teradek Bolt 4K 12G-SDI 750 RX wall mount

Needed a way to mount our Teradek Bolt 4K 12G-SDI 750 RX to the wall. I'm not sure if other Teradek products use the same bolt pattern. 25% infill 4 walls Rectilinear

Downloads
8
Likes
2
Rating
0
Order a print of this model
P
PrintablesLeavingthelegacy

10mm shower hook lock. Holds phone and towels.

This model goes with https://www.printables.com/model/1581584-phone-hook-for-10mm-glass-shower Print in at least PCTG

Downloads
8
Likes
2
Rating
0
Order a print of this model
P
PrintablesLeavingthelegacy

EDAC Blackmagic (computer) power supply wall mount

I needed a wall mount for a Blackmagic power supply. 25% Rectilinear 4 walls

Downloads
7
Likes
1
Rating
0
Order a print of this model
P
PrintablesLeavingthelegacy

Gorilla shelf trash can

I didn't have room on my shelf for a filament trash can, so I designed this. I was going to print a can, but then I saw the HDX quart cup sitting on my desk. Obviously, it is not designed to hold much weight, but it is great for all those…

Downloads
7
Likes
2
Rating
0
Order a print of this model
P
PrintablesLeavingthelegacy

Gorilla shelf plier pin

Material: PC-CF or PCTG Supports: No Brim: Up to your printer Infill: 15% Gyroid Use M6 nuts and bolts

Downloads
7
Likes
1
Rating
0
Order a print of this model
P
PrintablesLeavingthelegacy

LEE jeans button retainer washer

The button on my new Lee flexible jeans ripped through so I printed a retainer washer out of TPU

Downloads
6
Likes
2
Rating
0
Order a print of this model
P
PrintablesLeavingthelegacy

Quarter round molding corner bumpers

Our bathroom cabinets stick out in the middle which causes the robot vacuum to beat the corners up. These TPU bumpers help protect the quarter round. I used super glue to hold them in place and they seem to be holding up just fine. Print…

Downloads
6
Likes
1
Rating
0
Order a print of this model
P
PrintablesLeavingthelegacy

Tithe/opinion box collection bin

Decided to make an easier system for collection so we didn't have to dig all the tithing out from the bottom of the box. Designed for the Prusa XL

Downloads
5
Likes
1
Rating
0
Order a print of this model

These are all currently available results.