Counting matching models…
All models: https://www.printables.com/@MichalJ/models 📥 Downloaded it? Awesome! If you also hit 💙 and drop a quick 💬⭐, that would be perfect 😎. Got any 🔧 suggestions for improvements? Don’t hesitate to share!
Needed o-ring gaskets. Best from old connector. 📥 Downloaded it? Awesome! If you also hit 💙 and drop a quick 💬⭐, that would be perfect 😎. Got any 🔧 suggestions for improvements? Don’t hesitate to share!
📥 Downloaded it? Awesome! If you also hit 💙 and drop a quick 💬⭐, that would be perfect 😎. Got any 🔧 suggestions for improvements? Don’t hesitate to share!
📥 Downloaded it? Awesome! If you also hit 💙 and drop a quick 💬⭐, that would be perfect 😎. Got any 🔧 suggestions for improvements? Don’t hesitate to share!
📥 Downloaded it? Awesome! If you also hit 💙 and drop a quick 💬⭐, that would be perfect 😎. Got any 🔧 suggestions for improvements? Don’t hesitate to share!
Aluminum ladder hangers and more. Wieszaki na drabinę składaną z aluminium. All models: https://www.printables.com/@MichalJ/models 📥 Downloaded it? Awesome! If you also hit ♥ and drop a quick 💬, that would be perfect 😎. Got any 🔧…
Organizer na komplet nasadek 3/8" Yato 6mm - 22mm (17 sztuk) Wymiar: 209mm x 64,7mm x 17mm
Foam gun holder. Screwed to the wall, in the form of a latch. Uchwyt na pianę poliuretanową/montażową.
📥 Downloaded it? Awesome! If you also hit ♥ and drop a quick 💬, that would be perfect 😎. Got any 🔧 suggestions for improvements? Don’t hesitate to share!
Repair kit for: JCB 4CX Bruder 2428
📥 Downloaded it? Awesome! If you also hit 💙 and drop a quick 💬⭐, that would be perfect 😎. Got any 🔧 suggestions for improvements? Don’t hesitate to share! V.2 - ¼" thread (¼-20) Camera Quick Release Clamp from this project:…
Wall mount holder for pencil and inserts.
Screw-on funnel for the oil tank of the heating device. Strong construction. You can use mesh filter under funnel.
Use support. Use T-Nut Mount
Parkside 4V ARS 4 A1 board holder. Use T-Nut mount.
📥 Downloaded it? Awesome! If you also hit 💙 and drop a quick 💬⭐, that would be perfect 😎. Got any 🔧 suggestions for improvements? Don’t hesitate to share!
You need to print 4 pieces of sets to mount the saw to the work table. You need to use 4 pieces of threaded sleeve M8 and 4 pieces of screw M8 (length as needed minimum 80mm)
You need to cut off the protruding part, as shown in the photo, and glue in a repair piece. Mirror the part for the other side. I used cyanoacrylate glue and hardener.
30, 32, 34mm pipe holder. Pipe mounting between two walls.
Use support to printing revision_body Additional items: magnets 12mm x 3mm steel screw waschers max 12mm outside diameter x 1,5mm
You'll need: 24 cm of 160 mm pipe. 2 pcs M6 countersunk screws for mounted flap 1 pcs steel washer screw for attaching the magnet and the magnet housing glue (optional) a hole saw to cut the hole for the water pipe.
This bracket allows for quick installation of an exercise bar or playground ladder. The bracket accommodates a 30, 32, 34mm outer diameter tube. The bracket features a threaded hole for an M6 screw to prevent it from falling out.
Neede double sided tape. M4 screw lenght: max 35mm Hook diameter : 5,8 mm, end of the hook: 7,1mm.
📥 Downloaded it? Awesome! If you also hit 💙 and drop a quick 💬⭐, that would be perfect 😎. Got any 🔧 suggestions for improvements? Don’t hesitate to share!
Finishing te vox espumo skirting board.
Board (skadis)hanger for wolfcraft WF6957000. Hole spacing 40mm for skadis
These are all currently available results.
