Counting matching models…
Simple self draining tray to hold a round Scrub Daddy or other 100mm dia. x 40mm wide sponge. Feet at the back prevents it from sliding into the sink and a lip at the front drains water back into sink. Position at the back of the sink…
This is a modified print of the model posted at https://www.iter.org/newsline/-/3477 . The original model included files to print the entire model (complete 360°). The model required a printer with a print volume of 300mm x 300mm x 300mm,…
A 3D scan of a bicycle saddle. Prints nicely in PLA with 0.6 nozzle size. Requires lots of support underneath and careful removal to not damage the rails.
This print can be used to display award medals on a wall. It consists of two modular parts, a frame and a plate. There are two versions of each. The frame has both a simple version and a version with mounting slots to simplify attaching…
This is a remix of the Ledskof Raspberry Pi case. I changed the case penetrations to fit tighter and added some ventilation. There are 2 versions of the case bottom, one with a mount and the other bare. Revised 08-17-23: Added…
Designed this to fit a Whirlpool ice maker includes an insert that drops into the tray that can be replaced when stained or dirty. Print the insert on a textured sheet to help hide the water stains.
When disassembling the MK4s to convert to the CoreOne one of the pulleys was stuck on the motor shaft. Instead of yanking on the shaft I designed and printed this simple puller to print on the Mini+. Printed in PETG with 40% fill, flat…
Tiny tool to open a stuck Presta valve nut (not to remove the valve). These are quick to print and are small enough to throw a couple into a bicycle toolkit in case of emergency. Works best with PETG on 0.15mm.
A simple Ethernet Jack adapter plate for Pass & Seymour / legrand Ethernet Jack.
A simple mount to attach the Power Adapter in the upright position. Designed to fit the Prusa Mini+ power adapter.
While the Cascade Wallet works great I found that the bills would sometimes slip out of the money clip when in my pocket. I added a corner hook that holds the bills in the wallet tighter but still allows them to be inserted easily. Works…
A cowcatcher for a model steam train designed for S-gage, but can be scaled some to fit larger models. Works best in FLEX filament to prevent breakage. Used CA glue to attach to the chassis from the bottom.
This is a small handle to replace the hole in the Coreboxx MMU access panel. Make opening the door much easier and seals up the hole if using the Semi-smart heater. Printed in PETG with 0.4 nozzles default settings. Two versions of the…
Introduction This box uses the Parametric Rugged Box as a base to hold two trays to hold unto 7 assembled heater blocks with socks, thermistor and heater, 6 loose silicone socks, 35 E3D v6 nozzles and 7 loose Prusa Nextruder nozzles. The…
Two color gcode file for Prusa mini printed with 0.15, PLA.
A simple Nespresso Carousel to hold unto 35 capsules. The carousel sits on a ball bearing that's press fit into the base and attached with an M5 screw.
My goal with the remix was to integrate the mod into the printer so it could easily be turned on to use and have it be unobtrusive when not in use. The camera kit comes with 2 LEDs which are 3-wire digitally controlled. I deleted these…
Simple model to install a magsafe in the Mazda console. The TPU Blocks hold the plate snugly to resist the MagSafe force when removing the phone. Wedge the blocks into the holes on the end. They fit real tight and you will need needle…
Notes: This print is for a small control box with Light and Fan switch plus Fan Speed control. This is a companion to the remix referenced Enclosure Fume Filter. I mounted this to the bottom of the Lack Enclosure and used the single Power…
This print is a replacement for the tray in the CX-5 console. It includes a pocket that allows the Otterbox Charger (SKU 77-89453) to be slid into. Printed with supports. https://tinyurl.com/Otterbox-Apple-Watch-Charger Also included the…
Features: Remote location doesn't occupy space in the enclosure Quiet operation, fan can be placed on the floor away from the enclosure. Effective flowrate Uses standard square or round HEPA/Charcoal air filters Uses standard 2-½" vinyl…
These brackets use the existing cable tie holes in the corner channels and are quick to print. Attach the brackets to the Coreboxx frame using 3mm wide cable ties. Install the LED strips in the channels and install the covers and you're…
I got tired of dealing with loose pieces of Teflon tubing used for 3D printing and came up with this simple storage caddy for small diameter tubing. Prints well on the MK4S with no support but should work well with any printer that has a…
This model will print a pushbutton for the Sharp Microwave Door Release. Designed to fit Sharp Microwave Model R-530ES-T, may fit others. Printed with 60% infill in PETG, 0.4 nozzle and 0.2 layer height. Installation is simple, transfer…
These are all currently available results.
