Counting matching models…
I designed it for my DIY 3D Printer project. Enjoy! nema17param.FCStd is parametric FreeCAD sourse. SHA 256 checksum: b42b007f9a17d0b99fa42b244ce4feace04e35770caa8a4032f3b37cce8e85b2 nema17param.FCStd…
Material: PLA Layer Hight: 0.2 mm Nozzle: 0.6 mm or smaller Build Plate Adhesion: Skirt 3
By redesigning with FreeCAD, you can fit this holder into your sewing thread spools on your coverstitch machine, Babylock, etc. SHA256 checksum 8c31f2c0218e9d22fff83981654d53168124faf3a69c68335307313f5cc1c333 torneio.FCStd…
You can mount your Arduino NANO on a wooden board with this holder and 4 screws. It is good for direct soldered wirings. You can push the reset button easily. Easy access to the USB and ICSP connectors. Prepare 4 pilot holes in 17 mm x 55…
FreeCAD source codes are parametric.
To fix something around a screw rod M6円錐形化粧ナット 穴のあいているものをネジの中心に固定したいときに使います KnurledCone: insert an M6 nut DecagonConeNut: insert an M6 nut DecagonConeM6: already M6-threaded Tube-shape support materials are initially prepared in…
Height: 95 mm Four drill holes: 32 mm x 32 mm MD5 (kitchen.FCStd) = b948efb54d32d462692f081d28c40632 MD5 (kitchen.stl) = 11c1f1733e48d040f04a3986bd08209a Method: Material: PLA Layer Hight: 0.3 (Extra Fast) Wall Thickness: 1.2 Top/Bottom…
Scale hexhex8mm.stl with your slicer for your 3D-printer and for your drill/driver. How to 3D-Print: PLA With enough top, bottom and wall thickness With support material for the axis
Scale it 99-101% in x- and y-directions with your slicer to tighten or loosen it. It is a good idea to tap the thread after printing. ネジが緩すぎたりきつすぎたりする場合はスライサーでｘｙ方向に縮小または拡大するとよいでしょう。印刷後にタップでネジ穴を仕上げるのもよいでしょう。
Desk thickness (default: 31 mm) is an adjustable parameter in FreeCAD source. Requirements: Clamps M16 x 15 set screws M5 x 15 screws M5 washers M5 T-nuts 8 mm hex Allen key is here and there:…
I pasted Q508left and Q508right with some pieces of double-sided tape on a plastic sheet. There are holes to access USB and DC connectors in the left side. Material: PLA Support: No Nozzle Diameter: I use 0.6 mm
(In English) One of wheels of my suitcase was worn out. I put this PLA-3D-printed wheel cover on the worn-out wheel with four cable ties. I also put a "Silicone Luggage Wheel Cover" over the wheel. Ex.…
Requirements switch2020_XX.X.stl (XX.X is height in mm of two M2 holes.) two M2 screws one M5x10 countersunk screw one t-nut one OMRON D2F switch Enjoy!
Change diameters for your taps. Fix a tap with an M5 set screw. A toothbrush is useful to remove dust from the tap.
Mount a 3-pin IEC320 C14 Inlet and fused switch module under a DAISO Joint rack wire-meshed shelf! ダイソーのジョイントラックの転び止め棚の下に3ビンIEC320規格C14インレットユニットを固定するための箱 Requirements: * 1 powermounter.stl * 2 daiso.stl * 1 power connector with fused…
You can mount your Seeed Grove 4-Digit Display with this holder. Easy access to the connector. Materials and methods Build Plate Adhesion: Skirt Infill: 20% Filament: PLA Supports: No
Adjust height of your DAISO joint racks. etc. Use a rubber mallet to insert an M6 bolt into M6foot.stl. Use a 5 mm hex wrench to rescue a broken bottomjoint.stl. FreeCAD source of M6foot.FCStd and bottomjoint.FCStd are available.
A rigid edged cube can be made from two half parts and four pins. Insert pins into 4 edges with a small amount of glue to connect the half parts. You can easily alter the size of the cube by changing parameters of "PillarOuter" in the…
CAUTION: Do not get burns from heated water and kettles. Requirements for kettle.stl: M3x10 heat set insert M3x10 stainless screw 3x10x0.8 stainless washer Requirements for kettleM5.stl: M5x25 or M5x20 stainless screw 5x10x0.9 stainless…
[Caution] Screw this table tightly enough on the wall of your toilet, but do not put your weight on it. Use screws and anchors for gypsum boards, if needed. [Files] Fillet width of the top table of RightOpenSquare.stl is 0.9 mm. That for…
Cut down one side of coupling part with a saw. Fix the gear box to this stay with two small tapping screws. I use it to make a sewing thread winder, for example: https://gist.github.com/t-nissie/fbd639bcd427e46c7fdfc1529023d521…
I do not want my Roomba to dive into a 60 mm step, but want to clean the edge as much as possible. With 0.4 mm nozzle: Line width: 0.4 mm Wall thickness: 1.2 mm ETA: 5 hours With 1.0 mm nozzle: Line width: 1.0 mm Wall thickness: 2.0 mm…
NewScottie.FCStd is FreeCAD source. Adjustable parameters are in items of Top and TissueBox in NewScottie.FCStd, FreeCAD source. Default sizes are: Tissue box: 64.6 mm x 110.0 mm Line size: 4.4 mm x 12.0 mm Cabinet shelf thickness: 16.0…
Bracket for mounting a NEMA17 stepper motor to the bottom of a 2040 extrusion Category: 3D Printer Parts
You can make small boxes from a empty Kleenex box. Change the parameters of "Inner" box in the FreeCAD source for your purpose. For easy folding of the small box, scratch the original paper box with the back of Olfa around the jig.…
Put an one-dollar parasitic basket onto a VESA mount behind your LCD TV! Hide your recording HDD and wiring cables behind your TV. Adjust <<Base>>.Height parameter within 3-8 mm for your purpose in pin.FCStd FreeCAD source. M5pin4h.stl,…
End of the baseboard 巾木の終端です
I use 0.4 or 0.6 mm nozzles to print it.
You can add a wooden top board on your DAISO joint rack with this attachment. Adjust radii of the pole hole and the 5 mm hex wrench hole for your 3D printer.…
Default distance of centers of two 2020 aluminum extrusion profiles: 320 mm It can be changed in parametric FreeCAD source code. Requirements: Mounter plate Stepper motors M3 screws M3 washers M4 screws M4 washers M4 T-nuts
Offset height is adjustable parameter in FreeCAD source. Print it with 0.4 mm or 0.8 mm line width.
Pump Diameter: 12 mm I use 1.0 mm nozzle to print it.
tire.FCStd is FreeCAD source
These are all currently available results.
