P
PrintablesSpammy
Harley Davidson seat nut washer
PLA 100% infill.
- Downloads
- 148
- Likes
- 18
- Rating
- 0
All models
Counting matching models…
P
PrintablesSpammy
H-D wheel bearing packer
I made second version of the handle with knurled outer surface to help removing it after use. However, I'm struggling with the threads, since my modelling software doesn't support thread modelling, only textures. Had to use the coil…
- Downloads
- 128
- Likes
- 8
- Rating
- 0
P
PrintablesSpammy
Peugeot 207 hub cap
Printed in PLA and painted. You need a steel clip.
- Downloads
- 102
- Likes
- 13
- Rating
- 0
P
PrintablesSpammy
Nordic walking sticks rubber tips
Designed for my Trekker Black Wolf telescopic sticks, but then again should work for other sticks too, if the geometry is close enough. I printed them in TPU, 100% infill.
- Downloads
- 51
- Likes
- 7
- Rating
- 0
P
PrintablesSpammy
VW Transporter T4 shift lever bushing
I printed this for my friend as per dimensions given by him. While assembling, he noted that the shaft diameter should have been about 1mm tighter. A strip of tin corrected this.
- Downloads
- 43
- Likes
- 14
- Rating
- 0
P
PrintablesSpammy
180 mm vice jaw protectors
This is my second version, where I used three magnets in each protector instead of just one. Be careful about the polarity of the magnets, so you can store these protectors hugging each other compactly. For best strength use 100% infill…
- Downloads
- 35
- Likes
- 15
- Rating
- 0
P
PrintablesSpammy
Hozelock hose reel wall bracket latch
More robust design. I used PETG for it. Snug fit.
- Downloads
- 31
- Likes
- 1
- Rating
- 5
P
PrintablesSpammy
Farina pedal rubbers
Filaflex TPU with 15% infill worked fine for me. Supports are difficult to clean, but are not very visible anyway.
- Downloads
- 31
- Likes
- 3
- Rating
- 0
P
PrintablesSpammy
Emco Unimat 3 motor conversion
Converting the lathe for 5mm wide synchronous belt. Printed a mock-up from PE, but I did use them for real lathe work as well without problems. Lathe pulley has 14x1mm thread. Motor axle 14mm with 5mm key.
- Downloads
- 29
- Likes
- 4
- Rating
- 0
P
PrintablesSpammy
Harley Davidson replacement footpeg rubber
Haven't printed it yet. Please send pictures and/or comments should you end up printing a pair.
- Downloads
- 27
- Likes
- 4
- Rating
- 0
P
PrintablesSpammy
Peugeot 207 flip key roll pin removal jig
Jig to remove and install key blade to remote control key. I printed it with ABS. Should do the trick. Pictures show the original version also to get an idea what was changed / remixed.
- Downloads
- 19
- Likes
- 1
- Rating
- 0
P
PrintablesSpammy
Rubber spacer for rear bumper mount (BMC)
TPU with 25% infill
- Downloads
- 15
- Likes
- 0
- Rating
- 0
P
PrintablesSpammy
BMC Farina rear bumper joint pad
Black TPU, 15% infill, supports.
- Downloads
- 13
- Likes
- 0
- Rating
- 0
P
PrintablesSpammy
Sportster ham can rubber trim
Haven't printed this one yet, gotta practice slicing the model or borrow a bigger printer. TPU should work fine here.
- Downloads
- 13
- Likes
- 1
- Rating
- 0
P
PrintablesSpammy
Fisher Price vintage toy cash register cam shaft
Printed it with ABS 100% infill. Assembly will be tricky. You'll have to drill a mounting hole to green coin funnel to install the M6 nut. I used a nylon lock nut, so that it doesn't tighten up too much when income gets big =). It helps,…
- Downloads
- 12
- Likes
- 3
- Rating
- 0
P
PrintablesSpammy
Austin Cambridge Door Lock Setting Tool
Print it from ABS or PLA, doesn't really matter, since it does not have to be very strong to do it's job. Original might have been cast aluminum or magnesium.
- Downloads
- 11
- Likes
- 1
- Rating
- 0
P
PrintablesSpammy
Austin Cambridge Shift Lever Rubber Gaiter
Print it as flexible as possible. Picture of torn aftermarket rubber as attachment.
- Downloads
- 11
- Likes
- 1
- Rating
- 0
P
PrintablesSpammy
Farina rear leaf spring insulator rubber
This replaces perished rubbers round rear springs
- Downloads
- 9
- Likes
- 0
- Rating
- 0
P
PrintablesSpammy
K-125 Odometer gear
Please note. I made first mock-up model out of plastic just to see if it works. It worked fine for a short period of time, but wore out quickly. The final version is commercially printed from steel. It has performed well for years with…
- Downloads
- 8
- Likes
- 0
- Rating
- 0
P
PrintablesSpammy
Maserati Merak SS 1975 inlet manifold grill
Only one thousand of these were ever made, so sourcing of parts is fairly difficult. I printed it from Fiberlogy PCTG. Pictures show also the cracked original grills.
- Downloads
- 8
- Likes
- 1
- Rating
- 0
P
PrintablesSpammy
Scheppach BTS900 dust hose adapter
I printed it using ASA filament. Mounting from corners using four small screws (or glue, if you wish).
- Downloads
- 7
- Likes
- 1
- Rating
- 0
P
PrintablesSpammy
Motor stand for squirrel cage motor
My Emco Unimat 3 lathe's own motor broke down, as they so often do. So this is the first step to convert it to real AC-motor (400 VAC / 0,375 kW / 50 Hz). Printed in PE.
- Downloads
- 7
- Likes
- 2
- Rating
- 0
P
PrintablesSpammy
Austin Cambridge Door Lock Overtravel Block
Print it solid, it'll take some beating.
- Downloads
- 5
- Likes
- 2
- Rating
- 0
P
PrintablesSpammy
BMC Handbrake pivot axle bush
I printed it with Filaflex 60A TPU Filament, 100% infill. You might want to try a bit harder compound also. Lubricate well before installation with brake rubber grease or PTFE-lube. Remember, you need two of these. Have fun and gimme all…
- Downloads
- 4
- Likes
- 0
- Rating
- 0
P
PrintablesSpammy
Barrel adapter for IBC container tap
A handy thing for collecting rain water in your garden. I printed it out of ABS. PE would be very good, too. Fixed with a couple of tin roof screws and sealing was guaranteed with a bead of butyl sealant between the tap/barrel/flange…
- Downloads
- 3
- Likes
- 0
- Rating
- 0
P
PrintablesSpammy
Power file vacuum adapter
Silverline, Tamforce, Ryobi etc. with 13mm x 457mm sanding belt. I use same hose as with my Mirka Abranet block. Works fine! The other end is connected to a household fireplace ash vacuum cleaner with a TPU adapter. Snug fit, just plug it…
- Downloads
- 3
- Likes
- 1
- Rating
- 0
P
PrintablesSpammy
Beta / KTM sidestand bushing
One version for flanged bolt, one version for countersunk M10 bolt. Use partially threaded bolt to make it last long. I printed it with Fiberlogy PCTG. Sidestand hole diameter 18mm.
- Downloads
- 3
- Likes
- 1
- Rating
- 0
P
PrintablesSpammy
Farina Front Suspension Bush Kit
Set of bushes for BMC 1.5 liter Farinas. Models include lower wishbone bushes (you'll need 8 pieces) together with king pin to shock absorber bushes (4 required). Steel inner bushes required. Due to badge engineering, these'll fit the…
- Downloads
- 1
- Likes
- 1
- Rating
- 0
These are all currently available results.