P
PrintablesJáchym Tiskne
Screw holder
Same thing as original, but you can snap the screw in much easier (from the front).
- Downloads
- 922
- Likes
- 335
- Rating
- 5
All models
Counting matching models…
P
PrintablesJáchym Tiskne
Spongebob pen cup
Print all the parts (not the “Spongebob pen cup” file). Nozzle 0,4; no supports; chose the rest Using peaces of 1,75 filament, join the sides with the bottom part. Then add the front and the back and secure it with the filament (leave…
- Downloads
- 326
- Likes
- 71
- Rating
- 4
P
PrintablesJáchym Tiskne
Victorinox tomato knife cover
Print it laying on the site, the printer will bridge “across the blade.” If the blade doesn't go in, check the bridging direction and if needet adjust the angle of bridging in the infil tab (PrusaSlicer). If it still doesn't go in, lower…
- Downloads
- 297
- Likes
- 36
- Rating
- 5
P
PrintablesJáchym Tiskne
Pill box
Max. 16 Ø6x3mm magnets Best with 0.6mm nozzle or 0.4mm nozzle and 0.6mm extrusion width:
- Downloads
- 165
- Likes
- 29
- Rating
- 4.8
P
PrintablesJáchym Tiskne
Pot Lid Organisation
A set of models to organize your pot lids for easy acces. Atached with doubble sided tape.
- Downloads
- 148
- Likes
- 109
- Rating
- 0
P
PrintablesJáchym Tiskne
Pizza cutter cover
Cover for pizza cutter blade. Diameter 70mm (2.75 inch)
- Downloads
- 78
- Likes
- 7
- Rating
- 5
P
PrintablesJáchym Tiskne
Magnetic bit holder
4 bits or 2 drills magnetic holder for the parkside performance pabsp 20-li c2 drill. Maunted with the original screw. Bit holder can fit into the box with the drill. Battery can be removed freely. 8 pieces of 6x3mm magnets. Print without…
- Downloads
- 51
- Likes
- 28
- Rating
- 5
P
PrintablesJáchym Tiskne
Cable Zip Tie Mount
Recomend printing with 3 perimeters and 0.6 layer width (external perimeter and perimeter) for best strength. (but with 0.4 nozzle)
- Downloads
- 32
- Likes
- 7
- Rating
- 0
P
PrintablesJáchym Tiskne
Better pizza cutter cover
Print with 0.2mm layer (for the best bridging result). Made for 70mm blade.
- Downloads
- 28
- Likes
- 4
- Rating
- 0
P
PrintablesJáchym Tiskne
BOSCH screwdriver bit organiser
No supports. Posible with vase mode (ad more bottom layers).
- Downloads
- 24
- Likes
- 6
- Rating
- 0
P
PrintablesJáchym Tiskne
Book sleeve
I recomend putting some holes to the bottom of the case - it will be much easier to slide the book in and out. (yes, it is my wifes book XD)
- Downloads
- 20
- Likes
- 1
- Rating
- 0
P
PrintablesJáchym Tiskne
Iphone 12 pro case
This case for iphone 12 pro is very slim and snug, it fits tightly to your phone and is designet to be as little restricting as possible. I used my phone without case but my wife didnt like it, so thats why i made this. I have a magsafe…
- Downloads
- 12
- Likes
- 2
- Rating
- 0
These are all currently available results.