P
PrintablesHenri S
Shark Stratos Accessories Holder v2_Double
Holder for 4 accessories for your Shark Stratos vacuum cleaner.
- Downloads
- 295
- Likes
- 16
- Rating
- 0
All models
Counting matching models…
P
PrintablesHenri S
Simple phone holder for car vent v2
Print with 20% infill and 3D-honeycomb pattern for good results.
- Downloads
- 261
- Likes
- 15
- Rating
- 5
P
PrintablesHenri S
tp-link TL-SG105PE Switch 10 inch rack holder
You need zipties for the power brick. The switch slides into the mounting brackets and locks itself in place. There is also a version for 19 inch racks:
- Downloads
- 181
- Likes
- 30
- Rating
- 5
P
PrintablesHenri S
Toothpaste Organizer with adapter for smaller tubes
Print with supports everywhere. The diameter for the dispenser is 38mm and for the other two holes 43mm. If you have a tube with a smaller diameter (e.g. Odol-med) you can print an adapter for it.
- Downloads
- 70
- Likes
- 8
- Rating
- 5
P
PrintablesHenri S
Sponge Holder v2
Sponge holder with an added lip to fit a sink with a higher edge.
- Downloads
- 66
- Likes
- 8
- Rating
- 0
P
PrintablesHenri S
tp-link TL-SG105PE Switch 19 inch rack holder
You need zipties for the power brick. The switch slides into the mounting brackets and locks itself in place. There is also a version for 10 inch racks:
- Downloads
- 50
- Likes
- 3
- Rating
- 0
P
PrintablesHenri S
Slim Vertical Stand for External Drive (2.5 HDD)
Fits 2.5 HDDs with a width of 18.5mm.
- Downloads
- 45
- Likes
- 4
- Rating
- 4.67
P
PrintablesHenri S
Projector Mount Shelfbracket IKEA Malm Bed
You will need a piece of wood and cut it in size. Additionally you will need 4 screws to mount the shelf to the shelfbrackets. I used 3.0x16mm screws (for wood, as the holes are countersunk). You can mirroring/reflecting the shelfbracket…
- Downloads
- 45
- Likes
- 11
- Rating
- 5
P
PrintablesHenri S
Mailbox Flag Magnet
Prints in place In addition to the print you need: Magnet (3x8mm) and glue for it. Happy printing.
- Downloads
- 45
- Likes
- 4
- Rating
- 0
P
PrintablesHenri S
Chef's Knife vol 2
Remix of the Chef's Knife. I added pins to insert in the handle.
- Downloads
- 38
- Likes
- 3
- Rating
- 0
P
PrintablesHenri S
Tchibo-Kaffemühle-Siebträgerhalter-Delonghi Dedica
Der Adapter ersetzt den Auffangbehälter der Tchibo-Kaffeemühle. Er wird in 2 (3) Teilen gedruckt und muss noch zusammengeklebt werden. Der Clip ist optional und kann auch weggelassen werden. Damit nicht so viel Kaffeemehl daneben geht,…
- Downloads
- 36
- Likes
- 2
- Rating
- 0
P
PrintablesHenri S
US Mail Flag
You need two magnets (3x8mm) and glue, to put the base together (the flag between; doesn't need glue).
- Downloads
- 26
- Likes
- 1
- Rating
- 0
P
PrintablesHenri S
Gaggia Classic PID Holder (Rex-C100)
The holder for the Rex-C100 has 4 magnets, so it fits any Gaggia Classic machines. You need 4 magnets (3 x 8mm) and glue for them. The size of the hole in the back is 11mm, so 4 thicker cables and 2 for the temperature-sensor fit through…
- Downloads
- 23
- Likes
- 2
- Rating
- 0
P
PrintablesHenri S
Airblower bellow upgrade for Tchibo grinder
Upgrade your Tchibo grinder, great for single dose shots with a small amount of beans every grind to keep them fresh. The model replaces the lid of the bean housing and adds a bellow. After you grinded your beans you only have to give the…
- Downloads
- 22
- Likes
- 5
- Rating
- 0
P
PrintablesHenri S
Magnetische Saumhilfe aka Kühlschrankmagnet
Der Nähhelfer kann ohne Support gedruckt werden. Benötigt werden 3 kleine runde Magnete (3mm x 8mm) sowie Sekundenkleber bzw. PLA-Kleber, um sie einzusetzen. Danach kann das Modell als magnetische Saumhilfe oder als Kühlschrankmagnet…
- Downloads
- 22
- Likes
- 8
- Rating
- 0
P
PrintablesHenri S
Toothbrush Holder Adapter for Tandborststall (Oral B)
Suitable for nearly every Oral B toothbrush due to its downside opening like the original toothbrush. It is like an adapter for Oral B toothbrush holders so the toothbrush does not have to stand on the holder but hangs and can drain.…
- Downloads
- 20
- Likes
- 0
- Rating
- 0
P
PrintablesHenri S
Simple Monitor Stand Feet
The two screwholes are countersunk, you need short screws (M3 x thelengthyouneed). There are two versions, one with a closed housing and the other one with hexagonal shapes. You can print it without support.
- Downloads
- 15
- Likes
- 1
- Rating
- 0
P
PrintablesHenri S
Eureka Mignon Fork Cover
It prevents the fork and the portafilter from scratches. It simply klicks in place, sometimes a bit firm, so it can‘t fall off. Suggest to print in PETG, so it wouldn‘t deform with your preheated portafilter. It‘s also printable in TPU to…
- Downloads
- 15
- Likes
- 1
- Rating
- 0
P
PrintablesHenri S
Gaggia Classic Pro Steam Wand Drain Remix 2
Fits for bigger magnets (8*3mm).
- Downloads
- 13
- Likes
- 2
- Rating
- 0
P
PrintablesHenri S
Toothpaste Organizer Adapter
If you have a tube with a smaller diameter (e.g. Odol-med) you can print an adapter for it as you can see in the picture. Organizer (adapter fits inside): https://www.printables.com/model/942525-toothpaste-organizer
- Downloads
- 12
- Likes
- 1
- Rating
- 0
P
PrintablesHenri S
Map Bigge/Olsberg NRW Deutschland
Ausschnitt/Relief der Stadt Bigge/Olsberg - NRW - Germany
- Downloads
- 12
- Likes
- 1
- Rating
- 0
P
PrintablesHenri S
Power Outlet Cover Frame
For covering the holes in the wall beneath the power outlet cover (80*80mm). There are two versions: A two-parts-frame: The cover/frame can be attached without removing the power outlet. It slides in place, you only have to glue the upper…
- Downloads
- 9
- Likes
- 3
- Rating
- 0
P
PrintablesHenri S
Gaggia Top Box (for PID, dimmer, etc.) - supportless remix v2
It fits perfectly without support. You only have to modify the mounting-bracket of the PID and make it thinner and with an angle, as it comes in the way of the topper angled part of the box. The closed top only seems to be closed, if you…
- Downloads
- 4
- Likes
- 2
- Rating
- 0
These are all currently available results.