Counting matching models…
Made a remix of the original fan grill of voron 2.4 to add more airflow and less fan noise. The remixed parts have 3mm more space between fan and grill, and the cutouts for the airflow are bigger.
I have made some clips to lock the skid of rc helicopters for transport. 5mm, typical 450 size. 8mm, logo 600. 9mm, Align 700N.
I found one cover that somebody else had made, but i was not happy with the fitment, so i made my own from scratch. Use modifiers to create patterns. Designed for printing in abs. 0.4 nozzle. I used 0.2 layer heigth. MMU2s if multiple…
The dell Precision 7750 have a quite vunerable usb-c docking. This is a tpu support to release the strain of the connection.
Tpu parts to mount gopro camera, Iflight FC07704 gps module and tbs immortal t antenna. Printed in prima easyprint tpu 95A. with 0.6mm nozzle, 0.3 layerheight. 230 degrees c nozzle. 50 degrees c bed. 40% grid infill. Assembly parts. 2x…
printed with 0.4 nozzle. i used petg. use support.
Needed: -Raspberry pi zero w -mbus interface: google : «site:aliexpress.com usb to mbus slave» -4x M3x8 pan head screw for plastic -4x M4x8 pan head screw for plastic/M3 locknut and M3x10 machinescrew -available space in a cabinet with a…
A box for dji googles v2 cables, antennas and battery. The orange part is TPU. I used Primacreator Easyprint tpu. I used Pet-G for the rest. Box is printed with 0.6mm nozzle. Tpu is printed with 04.mm nozzle.
I used 0.4 nozzle, 40% infill and 0.3 layer height. Also uploaded G-code for mk3s/mmu2s with the flex in tool 1. On extruder: Back out the tightening screw until backside of screw is flush with locknut in filament door.
Printed in 0.2 layer height. 0.4 nozzle. petg. No supports. Original model by xKen
This is the SB2209 cable cover with added holes for additional cooling of stepperdriver.
prints with no support. 0.4 nozzle. grid infill. (i used 40%). Petg. 0.2 layer height.
Got annoyed that the ptfe connector was not securly fittet to the stealthburner on my voron, so i modified the cw2 main body (Commits on Jul 12, 2023) to fit a ptfe retainer. I used a spare ptfe connector from the prusa mmu3 kit. I belive…
Printed in TPU95A. I used 50% infill(grid). 0.2 layer height. 0.4mm nozzle. Cable from gps is abit tight to get into the channel for it, but it was more important to prevent too much flex.
Simple model, prints without support in standing orientation.
Use some old petg leftovers for this :)
To route the antenna below the rx battery. Used for Legacy vbar with mikado rx sat. This was the easiest way i managed to route the antennas on this model. Signal coverage is not optimal if seen straight from behind the model, but…
Box designed for outdoor assembly of sparkfun qwiik KIT-15209 rfid reader. Printed and assembled. I have tried to design this so water that enters the box should not reach the circuit board. Cable is to be pulled thru wall from inside of…
Simple model to attach a headlight to a bike handle, while still being able to use it as a headlight. Printed in petg, 0.6 mm nozzle with organic supports. Also, should be printed on the side for strength. See hodelyktfeste-v3-print.3mf…
Pla. 0.2 layerheigth. 15% infill. 0.4 nozzle. No supports.
Simple bracket for fastening a HP HD2300 on top of a Voron.
I have ikea wireless chargers that i have drilled into a couple of tables. However searching for the correct posision for the phone to start charging is very annoying. This is a centeringplate for the phone to solve the problem. :)
These are all currently available results.
