Counting matching models…
Intro This is a modular drawer for filament storage. Each unit can be stacked vertically and horizontally. The depth is determined by the size of drawer slides used. Check below for the list of fasteners and drawer slides that work with…
I wanted a better way to store my 17 gallon totes, so I came up with this rack. It's fairly easy to make and requires some 2x4s, screws and casters. Here is a cut list (all pieces are assumed as 2x4s at nominal 1.5" x 3.5" unless…
Lid raisers for the K1 Max help improve the clearance between the drag chain / filament tube and the glass top as Creality have designed it very very tight. The vents allow you to help prevent the temperature becoming too high inside the…
Introduction The Peggit system is a simple way to attach holders and organizers to your pegboard using simple automotive rivets. The clip easily attaches to standard pegboard with 1" spacing using 15mm x 12mm x 6mm automotive push rivets.…
Introduction The Peggit system is a simple way to attach holders and organizers to your pegboard using simple automotive rivets. The clip easily attaches to standard pegboard with 1" spacing using 15mm x 12mm x 6mm automotive push rivets.…
Introduction The Peggit system is a simple way to attach holders and organizers to your pegboard using simple automotive rivets. The clip easily attaches to standard pegboard with 1" spacing using 15mm x 12mm x 6mm automotive push rivets.…
Introduction This is a simple and cheap tensile strength tester for measuring relative tensile strength from filament samples. It's used to test the layer adhesion strength across various filaments or settings. Does increasing the…
This duct can be used with fiber lasers with threaded bases. The mounting holes span between 100mm and 112mm. It works great on Cloudray and Gweike fiber lasers. It adapts to a quick-disconnect duct. The magnets are 12mm x 8mm N52. They…
These models are for converting a drill-powered spray paint shaker (link below) into an automated solution. Just add a motor, delay relay module and some wire and you have your own paint shaker that can be fully automatic and hands-off.…
This exhaust duct attaches directly to the back of an xTool P2, replacing the existing duct. It lets you fit the whole machine closer to a wall and vent the exhaust left or right. There is a feature for adding a zip-tie to secure to the…
Introduction The Peggit system is a simple way to attach holders and organizers to your pegboard using simple automotive rivets. The clip easily attaches to standard pegboard with 1" spacing using 15mm x 12mm x 6mm automotive push rivets.…
Introduction The Peggit system is a simple way to attach holders and organizers to your pegboard using simple automotive rivets. The clip easily attaches to standard pegboard with 1" spacing using 15mm x 12mm x 6mm automotive push rivets.…
This is a simple and small holder for a brass brush to mount directly underneath your toolhead on the rear rail. It prints fast and only requires a single nut and fastener. You should be able to just any material as it's not near any…
Introduction The Peggit system is a simple way to attach holders and organizers to your pegboard using simple automotive rivets. The clip easily attaches to standard pegboard with 1" spacing using 15mm x 12mm x 6mm automotive push rivets.…
Introduction The Peggit system is a simple way to attach holders and organizers to your pegboard using simple automotive rivets. The clip easily attaches to standard pegboard with 1" spacing using 15mm x 12mm x 6mm automotive push rivets.…
Introduction The Peggit system is a simple way to attach holders and organizers to your pegboard using simple automotive rivets. The clip easily attaches to standard pegboard with 1" spacing using 15mm x 12mm x 6mm automotive push rivets.…
Intro This is a hose caddy and accessory holder I made for my workshop. It can handle roughly 20 feet of 4" dust collector hose. It has accessory holders for a floor sweep, dusting brush, crevice tool and 2 wand extensions in the middle.…
Introduction The Peggit system is a simple way to attach holders and organizers to your pegboard using simple automotive rivets. The clip easily attaches to standard pegboard with 1" spacing using 15mm x 12mm x 6mm automotive push rivets.…
This is a simple jig for making 1" x 2" labels on a fiber or diode laser. It's designed to hold aluminum business cards flat. The jig is best printed with a material that withstands high heat, as the cutting operation can heat up the…
This duct replaces the current inlet for better distribution over the top pre-filters. The original duct is only 3" and concentrates all the fumes/exhaust in a very small area, overloading a single spot on the pre-filter. This duct makes…
This foot pad goes under the standard ‘feet’ on the Prusa Box. It adds a tiny bit of damping and isolation, but most importantly it keeps the enclosure from sliding on hard surfaces. These are printed at 0.2mm, no overhangs or other…
These sleeves attach to shelf brackets so you can add 6qt bins for storage. Here is a list of what you might need: Shelf Standards . These hold the shelf brackets, the design is made for the double-row ones. The ClosetMaid, Project Source…
This is a simple holder for a 6" dado stack. It uses a 3" bolt in the middle to prevent layer separation and makes is it feel unnecessarily sturdy. The whole assembly consists of 3 pieces: the backer (which mounts to the wall and holds…
This is a simple part which helps align the new Cloudray protective cover and makes installing and removing it much easier. This simply attaches on the underside of the marking platform and aligns with the side panels of the enclosure.…
These are all currently available results.
