Counting matching models…
A small wall hook I've designed to hold my US license plate. Use double-sided tape. Instructions I've printed two at the same time, no supports, white ABS. The space on the back was made to be used with 3M's double sided VHB tape. The one…
This is the Deathly Hallows pendant from Harry Potter with a spinning ring. Instructions Just print without supports, the ring should spin right away. I've used black ABS in 0.15 mm layers. Category: Props
An adapter for a 120 mm fan in the front of the case, taking three 5.25" drive bays. The fan is held in place by four M4 (4 mm) screws, the adapter standard M3 (3 mm) screws, the same 5.25" drives use. I was able to hold it in place with…
This is a bag holder designed to make it easier and more comfortable to carry lots of plastic bags. Instructions I've printed the 20 mm version using ABS in 0.25 mm layers. The 20 mm version is strong, able to support at least 10 Kg…
I created this simple dumbbell that may be 3D printed because I had unused weights and wanted to put them to use, without buying another set of dumbbells. This also has the advantage of being lightweight, when compared to the metallic…
Duct designed to adapt a 92 mm fan into a dust blower. The design reduces the output dimensions significantly, theoretically leading to faster air speed and focused air flow. It requires a powerful fan with high static pressure, such as…
I designed this simple soap dish to keep my soap from getting soggy.
I've created this adapter to facilitate the interface between banana plugs and breadboards. It allows you to connect up to four banana plugs on each side of the standard 840 pin breadboard. Print Settings Printer: Metamáquina 2 Rafts: No…
Tool Bit Holder designed to hold 30 4 mm bits (5/32"). Print Settings Printer: Metamaquina 2 Rafts: No Supports: No Resolution: 200 Infill: 30 Filament: Filamentos 3D Brasil ABS White Notes: Very easy to print. If the holes come out too…
I've designed a simple support for the LG PH550G projector that holds it vertically at a 10º angle to the wall. It is used to project images at the ceiling, for watching movies in bed. The support is made of two parts linked by a T-joint.…
This is a replacement part for Corsair 120 mm fans SP120 and AF 120 (The ones I have were bought in 2013, I don't know if they kept the same design). These fans come with a rubber grommet that deteriorates over time, either because the…
This is a siphon with a cup on each end. The cups eliminate the need for suction before starting the transfer of liquids, you just have to fill the siphon horizontally and then hold it vertically. Instructions Printed without suports.…
This is an ear saver designed to be printed on 20x20cm bed at 45 degrees (large). It is much more comfortable than the smaller ear savers that grasp onto the neck. The two arcs fit naturally to the head and stay in place while moving. It…
This badgeholder is as simple as it gets, just two pieces that you glue together. It has a 4 mm hole for a keyring. Supports cards in the most common dimension, ID-1 (85.6 × 53.98 mm or 3.370 × 2.125 inches) The hexagonal pattern was…
Joystick case for the Nexus 4. The right handle also improves the speaker sound redirecting it to the user. Instructions There are two possible orientations for 3D printing the case: up or down. It only depends on where you think the…
I've created dampening feet for my printer (Metamaquina 2) to reduce its noise and reduce vibrations. I believe that the machine works better if its frame is able to move a little bit, reducing the stress on the structure while printing…
This is a dock for the Nexus 4. It should be used with LG's wireless charger WCP-300 Qi. Instructions Print this scaled to 103% (1.03x original size) for a looser fit. I haven't printed this exact part, but I've printed it's bigger…
This is a dock for charging the Nexus 4 using LG's wireless charger LG WCP-300 Qi Wireless (optimized position for the fastest charging). It also has a place for putting a wallet and two keychain hangers one on each side. Instructions I…
This is a filament holder I made for my Metamaquina 2. It snaps right on the top of my printer without any screws or assembly/disassembly. Instructions Just print the two supports and they should be ready to go. I used a 12 mm aluminum…
These are all currently available results.
