Counting matching models…
Little bit remixed model. See remix diferencies section. Thanks very much to Jaha for his great piece of design in original model and to kisscoool18 for his colored remix. Good job! These remixes can be now complemented by Radius Gauges…
MMU3 Buttons which perfectly fits micro switches and MMU3 electronics lid. Printed from Prusament PETG
Box for Dummy 13, which can be used as gift box or box to store Dummy 13 unfolded or assembled. It can be also used as stand base or pedestal for assembled Dummy 13. Box have space for Dummy 13 itself and also for various accessories. To…
Gardena to G1 adapter suitable for flat G1 sealing washer. Printed upside down with suports to get smooth place for the inner sealing washer. Thanks to Mike to his original model.
This remix complements previously published Radius Gauges 1-30mm remixes and together acts as complete measurement set of radius gauges. Thanks very much to Jaha for his great piece of design in original model. Good job!
This model extension was designed to be sure that the FINDA cable will be fixed inside relief channel correctly and will not pop out. Printed from PETG, 100% fill
Tento držák truhlíku s květinami na plastové okno vydrží i velký vichr a vaše truhlíky z okna nespadnou - tisk PETG na MK4, 0.4 tryska, vrstva 0.2 Držák se montuje zasunutím do originální spáry pod okením rámem anení tak nutné žádné…
!!! Be carefull - Check you charger for current compatibility with your AAA batteries first !!! We are not responsible for any damage or injury. AAA battery adapter to AA charger used to charge AAA batteries in AA charger. As a tip is…
Ergonomic Print Bed Scraper designed to perfectly fit the hand for both, right handed and left handed. Printed From Prusament PETG, nozzle 0.4mm, layer 0.05mm. May be it is overkill, but I chose this setting to get a sufficiently rigid…
MMU3 Reset Button which perfectly fits micro switch and MMU3 electronics lid. It is easy to install with electronics in place, therefore very fast instalation. Open MMU3 Elecronic lid Place smaller side of hole of Button inner part closer…
Remixed models of Screwdriver Handle to fit my old set of small screwdrivers (good for small terminals etc.) with broken handles. I found original handle model as nice and remixable for my use case. Here are 2 new remixes containing holes…
Sady vykrajovatek pro vykrojeni dilu na pernikovou chaloupku.
See photos for instalation. Holder is not invasive to car. I There are used pieces of double sided sticky tape on 3 places to fix holder parts on place.
Car phone holder - Dacia Sandero mounted into place of blind of back window control button. See photos for instalation. Holder is not invasive to car.
Holder for MK4/S black PSU to be mounted under (LACK) table or on wall (in my case). It is possible to print it even without supports, part around the screw heads need to be cleaned little bit afterward in such case.
I have created this tool to be able to mark exact place where to drill 8mm hole for wooden dowel when the board connection have to be done in the middle of board area. Using of this tool brings perfect results. See pictures to learn how…
Filament Spool Clip for 1.75mm filament and multiple types of spools. I have printed from PETG, nozzle 0.4mm, layer 0,2 mm, 15% infill Thanks to Anatolii Chorniy for his original design, I found most usable up to now.
First of all there is necessary say BIG thanks to Tanishq Manuja for his excelent idea of the Multiple Resistor Leg Bending / Lead Forming Tool !!! This remix modify it to be usable with components tape package and for resistors and…
Jabra Evolve 65 joint fix keeping earpiece still turning. Printed from PETG, nozzle 0.4mm, layer 0.1mm, 100% infill, support on printer pad Sometimes it could be useful to glue A and B parts together by superglue.
Holder for spice jar to be mounted into spice rack or under kitchen upper cabinets. It can be mounted by side screws or on top. Both variants are present in STL files here In SKP file for SketchupMake is whole design of spice rack, ready…
First of all there is necessary say BIG thanks to Tanishq Manuja for his excelent idea of the Multiple Resistor Leg Bending / Lead Forming Tool !!! This remix modify it to be usable with components tape package and for resistors and…
Printed from PETG (V0 recommended), 100% infill, no supports needed
These are all currently available results.
