Counting matching models…
Put it on your table or make it mobile by using 4x lorenkrampe to mount it on G scale log car wheelbase ( https://www.printables.com/de/model/335862-log-car ) How to build it: Put gestell2 into the slots of gestell1. Push Schwenktrieb…
Smaller version of https://www.prusaprinters.org/de/prints/114024-traffic-cone Scaled to match Bruder vehicles. I used Das Filament PLA Neonorange colorprint_heights = 10.6, 19.6, 28.6, 37.6
Standfuß für einen tiptoi-Stift von Ravensburger, damit er aus kindlichem Chaos heraussteht. Der Stift steht auf dem vorderen Rand der Hülle auf, die Spitze hängt frei. Getestet mit aktuellen und älteren Stiften jeweils ohne WLAN.…
Works with LGB/Playmobil and Piko standard couplers. Length over all 170 mm. Couping hook fixed in newer Version You will need: 1 ea frame (rahmen) 2 ea axle (Achse) 2 ea sleeve (Achshuelse) 4 ea wheel (Rad) 4+x ea pin (Achsclip) 2 ea…
First color change at 18.6 mm, afterwards every 14 mm. I used Das Filament PLA Neonorange A smaller version (1/16) is https://www.prusaprinters.org/de/prints/125324-traffic-cone
Wagon body for https://www.prusaprinters.org/de/prints/121230-quarry-tub Print in Place. If you print in multicolor you don't have to do a lousy paint job ;)
Fully printable version of a light railyway log car, based on the picture in Meyers Konversationslexikon 1905, Tafel “Feldeisenbahnen II”, Abbildung 8 +9 http://www.zeno.org/Meyers-1905/I/Wm06392b It carrys loads from ~20 cm up to ~42 cm.…
Button set designed to look like the wheels of an DRG Class 86 locomotive (1'D'1 - 2-82) https://en.wikipedia.org/wiki/DRG_Class_86 Scale 1/50
Juices packaged with Bag-In-Box are supposed to be stored with a slightly liftet rear side, to avoid air getting into the box spoiling hte contents. Put the box on this handy support to easily avoid that. Fits 5l Bag-In-Boxes. 10 l fit…
Simple G-Scale buffer stop, designed for being easy to print (lying on the flat side), easy to mount (push through rail from below between sleepers) and to work well. Not intented to be a scale model of a real buffer stop.
Rubber Loops Tool for wristbands. Extralong handle
My kids broke their cover flap of the container from a Hook lift trailer (Bruder 02035), so i need a replacement. I could buy a new one (Bruder 43521), but hey, i have a 3D Printer ;)
Customizable hair pin legs. Adjust thickness of feet, distance to edges, position and diameter of screwholes to your needs
Für die Optik mit einem Bodenlayer und Infill in Wabenform gedruckt und gefönt. Print with single bottom layer honeycomb infill, then carefully use a hot air gun.
Almost fully printed wooden train carriage. I had some 5mm cubical magnets, cylindrical magnets (d<7,h<6) sshould work as well, ball magnets would probably be best. Carefully glue the axles to the car, be careful not to glue the wheels.
Strain relief for LGB Controller 198983 from starter sets. Screwed in through designated screwing hole.
My butter storage cover broke, but since i never used it for butter i printed this railing to use it as a shelf for other stuff
These are all currently available results.
