Counting matching models…
Update: New tuned version available, find out more http://qczek.beyondrc.com/lrs-moxon-antenna-v2-tuned/ Just a frame for DIY Moxon atenna. Find out more on my blog http://qczek.beyondrc.com/moxon-antenna-for-lrs-tx/ Just uploaded…
Simple balancer to check CG of RC planes :) Category: R/C Vehicles
This is small brushless gimbal for RunCam 2 camera. You will need micro storm32 (or similar size) gimbal controller, two 1806 motors for roll and pitch axis, and single 2206 motor for yaw axis. Print Settings Printer: GATE 3Novatica…
Just simple case for rpi zero, Sony IMX219 sensor and AR9271HP WiFi card. Category: R/C Vehicles
This is enclosure for LRS i developed. Finf out more on project site. http://qczek.beyondrc.com/qczek-lrs-433mhz-1w-lora-rc-link/ Category: R/C Vehicles
Not tested yet, you can see how it moves if you want https://www.youtube.com/watch?v=nuYYCQDqobA&lc=UgzzM2lk92OTqofrYvh4
Just box for uruav dji analog board adapter. Find out more on my blog http://qczek.beyondrc.com/analog-vrx-box-for-dji-fpv-goggles/ Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: Doesn't Matter Supports: Yes Resolution: 0,2…
Hi, Using this adapter you can mount rp-sma pigtail and use any external antenna you want. There is no need to modify/cat/etc Taranis' case, just plug adapter instead of original antenna. Category: R/C Vehicles
Just strap holder for my new radio :) Print Settings Printer: GATE Rafts: Doesn't Matter Supports: Yes Resolution: 0.2 Infill: 60 Filament: n/a PLA Notes: Printed with support or left/right side as shown. Category: R/C Vehicles
Just mount for your camera or FPV monitor :) You should stop printing between 30-31mm and put M6 nut inside. You will also need 25-30mm M6 screw and CA glue to mount the knob. Category: Hobby
The the Pi1541 case for all the C64 retro maniacs. PLA printed. A “led lite pipe” is not required and hard to say if it would work, cause i can't print in on my fdm printer… Kris
just simple pan servo mount (for small 5g servo). It works :) Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: Doesn't Matter Supports: No Resolution: 0.2 Filament: n/a PLA Category: R/C Vehicles
Designed for my new radio :). Instructions After printing you need to use CA to glue both pars. Next mount internal connector put a little bit CA on 5pin connector case and install module (gently but quickly) into your radio. Wait 5…
secure mount for your dart Category: R/C Vehicles
Just prop guard for tiny qx80. Print Settings Printer: GATE 3Novatica Rafts: No Supports: No Resolution: 0.2mm Infill: 100% Notes: PLA Printed... Category: R/C Vehicles
Rotary switch for you x-lite radio. Find out more http://qczek.beyondrc.com/taranis-x-lite-5-positions-switch/ Print Settings Printer: 3novatica gate Rafts: Doesn't Matter Supports: Yes Resolution: 0.1 Infill: 100 Filament: n/a PLA…
Hi, Because Diatone "carbon like" products suck, I designed reinforcements which make frame stronger. There is also FPV camera mount included. Category: R/C Vehicles
This is box for QLRS. Find out more reading my blog: http://qczek.beyondrc.com/qczek-lrs-meets-taranis-x-lite/ Print Settings Printer: gate Rafts: Doesn't Matter Supports: Yes Resolution: 0.1 and 0.2 Infill: 60 Filament: N/A PLA Category:…
Something you need to make gate printer usable ;) Category: 3D Printer Parts
These are all currently available results.
