Counting matching models…
I made it to drill holes in PCBs. Used old hard drive, toner tube, smooth rods from cd-rom, I can't remember where I removed the springs. Power supply of old loptop. Motor RS-555. Some parts needs suport. Check video: Update aded 4 parts…
This is probably a problem in all golf 3. I printed petg, bcs i don't like print with abs. 100% infil. 2024-10 Update. V3 is only longer, V4 and V5 I made it more convenient to print at an angle without support. Inclined at 30 degrees.…
I repaired the castle. original https://www.thingiverse.com/thing:161975 Category: Buildings & Structures
I made a holder for two and four batteries with a handle to make it easier to carry. I printed it with PETG plastic, laid on its side. Supports are required.
Printed on Petg plastic. I made the entrance fixed with screws, because I plan to improve it in the future. How I Designed This
Made a house for rats. Check video https://youtu.be/jp08GaRfXHk Category: Pets
To make it easier and risk-free to print, I made it in 2 parts. The loop sticks into the hole. No suport. Enjoy!
All parts printed with standart setings. Print 2 of "zvaigzde_puse.stl" or 5 of "zvaigzde_5dalis.stl". Check video Category: Food & Drink
Flame printed 1 layer perimeter, 0 layers top, 0 layers botom Electronic candle improvement: https://youtu.be/NLtmb8IC2uQ video How I Designed This Category: Decor
All parts printed with standart setings. to make square you must print 2 parts of "keturkampis 3x3" or 2 parts "2x2_kvadratas". To make triangle you must print 3 parts of "trikampis". check video 3x3 - 30mm X 30mm, 2x2 - 20mm X 20mm How I…
I got tired of holding resin vat over the bottle until the resin dripped, so I made a holder. Don't need suport. Check video Print Settings Printer Brand: MK3 Printer: Prusa i3 Rafts: Doesn't Matter Supports: No Resolution: 0.2mm Infill:…
I recommend printing with petg plastic and need support video
I made a plate for a large strawberry pot to stand on. I downloaded the little strawberry from here https://www.thingiverse.com/thing:3695423 and enlarged it by 520%. I used PETG plastic. Check video https://youtu.be/v79uY4kWx5M
I needed it, I couldn't find a suitable one, so I made it. You don't need to tighten the screws very much. The only difference between 10mm and 15mm is the thickness of the central part. Check video: https://youtu.be/HwB9THFWT2w
Standart setings. check video How I Designed This Category: Vehicles
The grille plastic I bought didn't fit the speaker holes, and I didn't want to grind or break anything, so I printed those that fit. check video Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: 0.2…
To put the ring back in place, you will need to unscrew the grill, put the ring back in place, and screw the grill back in place. I stuck colored labels on the console with double-sided tape. Category: Gadgets
When they put the gas in, they didn't ask me where to put the gas control, they did it as it was more convenient for them. The button was attached with double-sided tape, which later came off. I decided to make a pin for that button.…
The knob is in two parts. Covers the reset button, so it is impossible to accidentally press it. I very, very rarely use the reset button. Don't need suport or raft.
The funnel can be used with or without the strainer. The inner diameter of the funnel is 90 mm. The ring is designed to press down the edges of the filter to prevent unfiltered liquid from leaking through.
Head of Steve from minecraft - storage
I know it can be bought inexpensively, but I wanted to do it myself. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: 0.1 Infill: 25% Filament: Spectrum Flex pacific blue How I Designed This…
All parts printed with standart setings, and 100% infil check video Category: Outdoor & Garden
It was necessary to cut a lot of holes in the film. To save time, nerves and health I made a divider / cutter. check video How I Designed This Category: DIY
Printed with standart setings, just 1 part need suport. Bear head: https://www.thingiverse.com/thing:2335909 How I Designed This Category: Sculptures
I don't know what car the knob came from, they just gave me a broken one and said "do something." Does anyone know what kind of car this is? Check video
All parts printed with standart setings. Hood need suport and recommended PETG filament. Check video How I Designed This Category: Decor
You need to unscrew the original short screws and screw in the longer ones. To make it easier to tighten the nut I made a key. Any tube or rod can be used to hold the spool. I used a bad (scratched) smooth rod. Print Settings Printer…
I have a few rats. They like to lie in a hammock. Rats are rodents and there is nothing strange about breaking hammock limbs. Sew new pointless - they cut again, so I printed. Printed with standart setings. Check video Print Settings…
This thing was made with Tinkercad. Edit it online https://www.tinkercad.com/things/iT8Fa8cBObM video How I Designed This Category: Outdoor & Garden
The buttons on the tape recorder were broken. I printed the prostheses and glued them on. Check video https://youtu.be/IVWlkcGp7GQ
Gift joke “color the minion” or a gift that will be remembered for a long time. Printed with PLA plastic. Paint - Nail Polish. Minion Dave: https://www.thingiverse.com/thing:403110 https://www.thingiverse.com/thing:712321 Print Settings…
I used PETG plastic. No support is needed. I hung up the first nest box, and while I printed and assembled four more, starlings moved into the first one. Check video:
The standard trim didn't fit, so I made one. I did not save space. check video
I suddenly needed a UV chamber, so I quickly created a simple UV chamber from what I had. I didn't have much time, so I corrected the mistakes by drilling and gluing the missing elements instead of printing a new one. This saved me time…
I don't know what kind of lawnmower. They brought a broken part and asked me to do something. I did something. The first time before screwing in the screw - you need to heat it up and turn it hot. Category: Replacement Parts
This project is easy to print and assemble. No suport, no raft. Perfect for anyone into 3D printing, DIY projects, and practical solutions. check video https://youtu.be/7ZpxpdBN5s0
I decided to build a UV chamber with a timer. I used a timer switch and a motor from a microwave oven. I also used several platters from old HDDs. The power supply and UV LEDs were purchased. The aluminum profile is 20×10×220 mm. The…
This project is easy to print and assemble. No suport, no raft. I used PETG, because i will use in car. Perfect for anyone into 3D printing, DIY projects, and practical solutions. check video https://youtu.be/7ZpxpdBN5s0
These are all currently available results.
