Counting matching models…
The rod that goes into the extruder idler gear on the extruder arm likes to come loose. this will fix that. i have to push my pin back in after long prints or i end up with extreme under extrusion. this keeps the pin from getting to that…
This is a Shorter under the drag chain connector for the SV08. Use supports. This uses the exact same 10x15mm Drag Chain that is provided by solvol. I get no kick back for this. https://a.co/d/bmJhGwp
ok i have fixed the old versions flaws and now this works great. make sure to have the fans blow away from the board. the MCU fan now blows out the original hole. you can make these changes in your printer.cfg to have the fans use PID.…
The spool holder for the SV08 is... too smooth. strange problem, i know, but i was having issues with my new rolls spinning too fast and wrapping around the arm. this let you tighten the screw and add tension to the shaft. super simple,…
nothing fancy but make a huge difference. just place them under the bed in the holes and tighten as needed. be careful. the mount points are plastic and may brake. ( aka i broke one in testing :( ) if you can use TPU unscrew the 6 screws.…
lowers the probe to the recommend z-hight for the stock nozzle. no supports should be needed. print in asa/abs us m3 screws. offsets should be close to: z_offset: 2.5 x_offset: -18 y_offset: 16 recalibrate G28 X Y G0 X175 Y175 Z15 F6000…
sv08 build plate alignment to help center the build plate better.
this is heavily inspired by https://www.printables.com/model/957985-voron-24-bamboo-a1-brush-bucket this purge bucket has be designed for use with the sv08. the file needs to be modified so that your nozzle rest to the left/center of the…
made 2 versions. one with the original mounting nuts and one for heated inserts. M3 4mm this will be way lighter, stronger, and set at a better location then the thrown together last minute mount, they have for the official release. I got…
link to my files im using https://github.com/Val-dose-things/Jabberwocky_files LDO Jabberwocky SV08 mount (will need feedback for the SV08 MAX and ZERO. I'll make a lever stop shortly. the 2.5x8mm screws are used for mounting the lever…
this is a nuclear option. would suggest the other options i have first. needs to be ASA or ABS. You will need to locate the bolt holes for the aluminum plate. Lots of options. I have one to. only glue the build plate alignment and the hi…
didn't like the ones i found so i made my own. just extend it in your slicer to the size you need. fun fact may have to shrink them up to 10%. my ender 5 pro i had to scall the width to 92% but they are loose on some parts of my ender 3…
it should work with any printer it will fit on with an adapter clip. 2 spools and extruder mount for one you will need: 4 16mm M5 screws. 2 10mm M5 screws. (for the stabilizer) 4 16-18mm M3 screws. 4 M3 heat inserst or 4 hex nuts. 2…
i fixed a few spots that i was having issues with braking
this is a much tighter fit and clips on to the top rail of the SV08. also split the CoPrint stepper mount
The original was a bit tight so i just moved the faces to make it fit better. made it so you can mount the thermostat in any corner.
z_offset: 2 #if you have a lot of issues try 2.5 x_offset: 33.9 y_offset: 0 need 2 M3 heated inserts and 4 8mm M3 screwss I used demon eddy. will make eddy useful. https://github.com/3DPrintDemon/Demon_Eddy
used the: DIGISHUO 7 Inch Touchscreen Monitor for Raspberry Pi 4B/3B/3B+/2B | IPS FHD 1024×600 | Responsive and Smooth Touch | Dual Built-in Speakers | HDMI Input…
use M5 6-10mm shrews. this is mounted on my svo8. works great for this bed.
BDsensor mount for the SV08 parts needed: BDsensor cr touch 10mm cable 1 m2.5 8mm flat screw. Micro JST 1.25 4-Pin Female for connecting to the 5v uart. do to needing to compile klipper with the BDsensor you will need to be on mainline…
this is to add active cooling to the PSU pushing the hot air away from the mainboard. This can be used even if the PSU just by mounting it to the side. Suggest using ASA if you do. you will need 2 4010 fans a Y jst XH2.54-2Pin splitter…
it should work with any printer it will fit on with an adapter clip. 2 spools and extruder mount for one you will need: 8 16mm M5 screws. 4 10mm M5 screws. (for the stabilizer) 8 16-18mm M3 screws. 8 M3 heat inserst or 4 hex nuts. 4…
fixed some modeling errors and made it so it has the original mounting option still.
i made it so it clips on
just do 100% infill only adds like 20 minutes and will be way stronger. this should help for setting up the BL Touch: https://github.com/knutwurst/Marlin-2-0-x-Anycubic-i3-MEGA-S/wiki/Beginner's-Guide-(English ) should be offset with M851…
just do 100% infill only adds like 20 minutes and will be way stronger. this should be able to be used on either side. this should help for setting up the BL Touch:…
this is a remix for the Voxelab Aquila Category: 3D Printer Parts
had some issues with the screws. fixed that
4040 display and BTT pi mount
left side version Category: 3D Printer Accessories
This is a remix that allows for you need to put your glue stick or lighter in the hole. Category: 3D Printer Accessories
These are all currently available results.
