Counting matching models…
Nike shoe boxes come with a sticker on the side of them showing the product information. Many times, people discard the box, but if you're like me and want to save the stickers, you need a place to put them – that's where this design…
This is a 9mm ammo holder designed to fit into a Holosun optics box. I tested it with a Holosun 508T box, but other optics fit as well, specifically other rifle optics. It was designed around a 120 mm x 90 mm box. It stores 70 rounds, in…
A drop-safe holder for 12 soldering iron tips. Built to specification for this: Features both an inner protector and an outer protector – fits tight enough so that the tips will not fall if the holder is upside down.
Imported from Tinkercad. Kudos to: [lhmsgame](https://www.tinkercad.com/users/kurUzRNtsJk-lhmsgame) https://www.tinkercad.com/things/aGLH5BRT2Eg-ikea-laiva-bookshelf-hook-extended
This is a simple container designed around Playstation 5 games. This lets you easily ship Playstation game cases (by protecting the thin plastic of the case) or easily stack the games vertically. It comes with a lid that's a press fit. A…
This is a 1:1 scale model of a standard PCSL target. The design is based off the diagram from Section 7 of the PCSL rulebook linked below. The “K” and “A” targets are highlighted with a small “lip”.…
A very simple iPod Nano box. Tested with 5th generation, other models fit if they have similar dimensions. Has a little bit of room on top to fit an extra cable. Press-fit lid, can be held upside down without opening.
This mount allows you to attach a Rexing V5 (or V55 – or any other dashcam that uses the same mount) to a tripod. Rexing cameras have a UVC mode that lets the dashcam act as a webcam, which is neat. Has support for both “small” (¼-20 UNC)…
This is a simple PCB holder for the Stemedu micro SD card breakout board. This fits onto the holes in the PCB and has a thin layer of protection on the bottom. Using the holes in the PCB, there is a 2 mm thread which you can screw a nut…
This is a stand for Geekworm LVDS to HDMI adapter board. It uses the 4 mounting screws on the board as support columns. The columns have an M3 thread allowing you to secure them with a nut. The bottom of the stand is labelled for…
This a simple board holder for the Treedix USB tester boards (ASIN B0BW8ZC7YD). It uses the top two holes on the board to index and it protects the back of the PCB from whatever surface you're on. If printing with PLA, I recommend using…
A dual-camera mount for the Yi Home cameras, featuring two tripod mounts (¼-20 UNC or 3/8-16 UNC) on either side. To minimize material, the screw thread depth was kept very short, so these aren't recommended for rugged use.
This a simple press-fit cover for both the motor/drive component and the blades of a MasterChef immersion blender. This is useful for both protecting the blades when storing this, and also keeping rust/dust for forming in the motor.
Happen to lose your Holosun optics box, but still have the lid around? This is a replacement box. I've found that so far, all the Holosun optics box use the same lid size, so this should fit universally. There is a 0.2 mm clearance so…
Most cuttable LED strips come with a flimsy protective roll. This part covers that roll, offering protection for the LED strips, allowing stackability, and has a slit to allow you to easily cut them as needed. I have 2 different styles…
A common mod for ReplayTV units is adding a new hard drive, especially an NVME or SATA drive rather than the existing IDE interface. This part provides a mounting bracket pattern that you can either integrate with your own mount design…
This is just a simple cover for the pins on your Kingst LA5016 logic analyzer. Other models that have the same 32-pin layout may fit. The tolerances are really small so I recommend printing it with as small of a layer height as possible.
This part is a mold of the inner cavity for a dishwasher's tower protector. https://www.appliancepartspros.com/whirlpool-protector-tower-wp8268825-ap6012262.html You can use this design to make your own piece from or simply as a way to…
This is a simple press-fit base protector for the bottom of a APTSPADE Coffee Tamper. May work with other 51 mm coffee tampers.
This is a base holder for the IPEVO VZ-R document camera. It's compatible with the original screws (with a few mm added for clearance). Because most filament is very light, it doesn't work well on it's own as a base – it doesn't weigh…
https://x.com/ptrschmdtnlsn/status/1914839889432236490
Simple stand for the Cyberpower CNKD0401-14004A3 V01 LCD board. Uses 3 of the 4 holes on the board as index points, and provides access on the rear for the 11-pin connector. Approximate size: 70 x 90 x 17 mm Approximate mass: 15 g at 5%…
This a very simple press-fit box for a Celestron 66x eyepiece.
These are all currently available results.
