Counting matching models…
I tried a helmet hook here, it didn't hold the helmet securely. Printed this larger one, hopefully it turns out well EDIT 03/19/2019 I printed both models and they hold the helmet very securely. I am going to do some slight tweaks, I will…
Edit: The jig has been remixed and improved by another printables member! Please see: https://www.printables.com/model/1152988-emporia-vue-v3-esp-home-flash-jig-w-fixed-toleranc/comments Good luck with your project! Also I made a mistake.…
just some flanged washers for some body work panels Category: Automotive
I use this to put bevrages on my peg board. I used a lot of plastic at a little bit of infill so that it insulates the cup. Also acts as pen holder. Category: Organization
Print the top near where the skate bearings mount with a modifier and 100% infill. The first balancing stand is actually untested, the 2nd balancing stand is tested, but if you push it the wrong way, without a lot of infill, it affects…
This just mounts my build plate cleaning materials on the wall right next to my 3d printer. Hope you enjoy it! If I remember correctly this should use m3 screws. Get back with me in the comments if you find otherwise. Category: Organization
I designed this for an experiment that was later cancelled. As a result, I have only moderately tested the desigh and I have not revisited it to make some improvements. If I did it again, I'd make a relief for the nut that secures the…
Want to replace your electrodes with universal ones? Here you go!
I wanted something to mount my mini pc on the underside of any surface, so here it is! I have two different end pieces, so that I can slide the pc in and out without removal of the mount. Also, you can mount it vertically and keep it more…
Use this spacer ring to put a 40mm led ring around your H7? halogen or led bulb. recommend nylon but if your bulb is of lower wattage pla might work. Print Settings Rafts: No Supports: No **Resolution:** 200 Infill: 20 **Filament:**…
Part of my modulat peg board organization system. Holds an Amazon Alexa on the wall Category: Organization
I could not find a hot swap bay that met my budget requirements of $6, so I made one. You just need to add a connector, a sata to sata connector with bolt holes and use some m3 screws and nuts to make this work. The connector you need is:…
I use this to mount old CVS precription bottles onto my pegboard. I use these bottles to organize small parts. Part of my modular peg board mounting system. Category: Organization
EDIT: If needed, please adjust the scale of the model by 10x, i.e. add a 0 to the scaling. Incorrect units on export. Use this print spacer to print 3X5 index cards from your brother laser printer note: the revision2 has a relief to…
Use this to flash your sonoff device!
this can hold a veypor and two toggle switches. good for heated grips and heated seat switches you need some m6 nylock nuts and some m6 bolts, cant remember the size this fits right between the handle bar clamps on my drz400E. Category:…
Use this to mount an Estes model rocket onto your peg board. Rockets sure look nice mounted on the wall! Category: Organization
These are stands and tools to work on your aprilia SR50 fuel pumps! The round part with the square hole can be used to lightly tap down on the fuel pump cover to help work in some silicone lubricant for removal. The stands just help you…
I made a lot of mistakes buying wrong parts for my lml (Genuine stella) and I had to get rid of the steering lock to make this part, so that I could tweak it to make the stock key cylinder turn my aftermarket switch far enough for it to…
Use this to mount 1/2 emt conduit with a one hole strap. May also function with a two hole strap. May also work with pipe Category: Other
3d print, insert m6 nut, grind off nubs from broken OEM aluminum bit, instal & ride! Probably not safe to use these with an aftermarket rack. P.S. you should use the model with the step. It helps the plastics install a little easier…
Use these to mount an epson label printer on peg board and mount label tape holders right next to it. Works good! Obviously print the upper pegs with solid layers using a modifier Category: Organization
I wanted to have some fancy way to make switches with logos and stuff on them that I could expand or contract to include any mumber of switches that I wanted, with not too many, and not too few for any respective job. This is a good…
2000 honda insight IMA delete hole cover. This covers the hole that will be left upon removal of the IMA air vent. Category: Automotive
You can use these in order to splice together your 1/4" flex conduit / wire sleeve and make it make corners, split into tees, or even a cross! Category: Hobby
These are adapters I made to mount the mosquito hotend to my Prusa. The pinda probe holder has been redesigned to make it such that it is much more durable, I always used to break those! I had to scrape together the old files and I think…
https://sites.google.com/georgiasouthern.edu/michael-woodcock/projects/rat-basketball Please view the project page to know more about these files for teaching rats how to play basketball
If you remove the innards of the microsoft lifecam, you will be able to use these tools to focus the lens and mount it to other things. Mostly I have the wrenches and tools to focus the lens. They work good. Sorry for the mess, I am…
I made a few things as modular as possible here. You can bridge the panels together, any number you want. You can use the feet as feet to mount it on a flat surface, or, you can even mount this on the wall and use the "feet" as something…
I am crazzy about protecting my equipment. This is a camera protector for the industrial camera that comes with our scanners. Category: 3D Printing
I wanted something better than blocks of wood to hold my engine up while I worked on it. This is what I wound up with. they're so high so you can put the crankshaft thru, install the flywheel, do all of that stuff and still flip the thing…
When you use a NOCO battery, you have a ton of extra space. Use it to mount your CDI! V2 uses a sleeve to wrap around the noco nlp5 battery and the top holder to hold it 100% securely together. Not needed, but it's a finishing touch. The…
This is a pipe saddle specifically for 1/2" pipe to mount it with a one hole strap to whatever you need to mount it to. Category: Other
This is sized for the T2 rack. It would have to be modified slightly for a rack with less depth. Uses a c14 inlet. I printed in CF reinforced PLA & a 0.6mm nozzle.
I made this to mount an M8 turn signal securely in the OEM mount. Update: The indexable adapter allows you to use an m8 locknut to index the aftermarket turnsignal into the correct orientation. If when tight the light is at an angle,…
just some Sachs Madass 125 Accessories as I make them. Nothing fancy.
V2 is finely adjusted for my printer and a 0.8mm nozzle, if you find the fit a little off, try the earlier model!
I noticed my Z2 MINI G4 ran a little hotter when running without the sata drive. My guess is the air was staying inside rather than being forced out. So I made this blank off plate to help force it outside of the case after going through…
Just to fill in the flex io port on these minis.
These are all currently available results.
