Counting matching models…
Instead of putting in batteries one-by-one, with this you can dump them in and take one as needed. Should also help you take the oldest battery first. It should let you hold AA, C, and AAA batteries (AAAs are shorter so they may rattle…
Holder for 10 SD cards. Slots alternate left and right and stepped up towards the back to make it easier to remove them. My other gridfinity designs . Based off Zach Freedman's gridfinity system .
Hold up to 6cm diameter spools. Slots in front provide area to store wire leads providing multiple options depending on the width and number of spools. My other gridfinity designs . Based off of Zach Freedman's gridfinity system .
My other ornament designs: Kelly Egan's ornaments A spiral sort of similar to an icicle. There is a small cap to finish off the top (I super glued it to the main ornament) and a hole through for hanging. I printed it without any supports…
Kelly Egan's ornaments Updated version with multiple colors: Multi-color Christmas tree A Christmas-Tree Christmas Tree ornament. You can see my other ornament designs here: Print instructions Category: Decor Print Settings Rafts: No…
My other designs: Kelly Egan's ornaments A pinecone Christmas tree ornament. Print instructions Prints as two parts, the cone printed in spiral mode with slightly thicker walls 0.6mm and a cap.
This is an adaptor to convert a GoPro mount (either side) to a standard 1/4-20 tripod mount. Print instructions Category: Camera Post-Printing A 3/4 inch 1/4-20 bolt is pressed into the mount base and a 1/4-20 screw can be glued into the…
A simulated red plastic cup for storing of pens or other solid objects. Beverages will likely leak out. Print instructions The vase gcode has a pause at the rim so you can change the color from red to white. The walls are slightly thicker…
This is a library of OpenSCAD modules for mounting Arduino boards. It has modules for creating enclosures, bumpers, mounting holes, punch out holes for jacks like USB and power and board dimensions. If you are making a custom enclosure or…
Hold 16 solder tips for Hakko FX-888D. May work for other iron tips as well. Holes are 6.45mm in diameter. My other gridfinity designs . Based off of Zach Freedman's gridfinity system .
My other designs: Kelly Egan's ornaments These snowflakes sandwich tulle (mesh fabric) in the middle of the print, which suspends the center design of the snowflake. Print instructions The gcode has a pause in the center for laying the…
After designing my hopper for AA, AAA, and C batteries didn't want to leave out the 9V batteries. Can hold up to 12 9V batteries. Takes up 2 x 2 x 2 gridfinity slots. My other gridfinity designs. Based off of Zach Freedman's gridfinity…
My other ornament designs: Kelly Egan's ornaments There are two versions of this ornament, a single and double version. The double version is thicker and mirrors the single version in the z-axis. These stars were designed in Python and…
A simple icicle type ornament. Prints best in vase mode with a brim. Includes a separate cap. My other ornament designs: Kelly Egan's ornaments
A zoetrope is a pre-cinematic animation technique where a series of animation frames are placed inside a spinning cylinder. Slits in the cylinder make the frames of the animation visible for only a fraction of the second creating an…
This mount encloses the camera and mounts it to the rails under the bed. Designed for an octoprint or other print monitoring setup. You will need 2 t-slot inserts and M3 10mm screws to mount the base to the rails. I printed these t-slot…
This is a remix of the lid piece of LoboCNC's Blinking Cat Glasses . Go to his page to download the remainder of the parts to make these glasses.
The case can be used alone for a Raspberry Pi 3B+. The mount lets you attach it to a Prusa MK2, MK3 or MK4 printer frame for use with Octoprint.
These are all currently available results.
