Counting matching models…
A friend of mine wanted something to plug the headphone port on his iphone since it gets used in a very dirty environment and he doesn't use the headhpone port that often. So I modeled up this dummy plug which I modeled off of a 3.5mm…
This clamps on to the bow limbs and holds the bow upright. Can be used in different positions on the limb depending on bow config to keep it upright. Instructions Print out 2 pieces then bolt together with M8 hardware. The other two…
16Nov2024 - Uploaded V2 model which has a shorter front wall and deeper cut to the rear with a larger radii up to the top. This was created to provide a splash guard to the PETLIBRO DockStream pet water fountain in order to prevent water…
These mounts allow you to mount the Logitech circle view at a higher angle than the included 20deg mount. These allow for 30deg ,35deg, 40deg, 45deg, 50deg depending on which you download. Mount this to the house and then mount the…
This is a replacement lever arm part for a Samsung moveable ice maker. Category: Replacement Parts
This bracket is used to mount VG80 light bars to the Modular Hydroponic Tower Garden. Use the metal bracket included with the VG80 light bar and mount it to the support using an M3 bolt and nut. Then the light bar will clip into the…
This assembly is used to help set the center shot on a compound bow. To complete this assembly the following is needed: Hardware: 4 - 10-24 countersunk head x 1.5" in length 2 - M6 Washers 1 - M6 Nylock Nut 2 - M6 Standard Nuts 2 - 10-24…
This plug is used on a Litter Robot to allow removal of the internal shield on older models. This plug matches the plug design used on the newer models. Printing: I printed using PETG at 0.2 layer height with three perimeters on a Prusa…
The upper half of the latch on my Plano bow case has broke twice now. Instead of waiting on a replacement I figured making a printable replacement would be quicker and allow for easy replacement in the future. Category: Other
This will replace the plastic ignitor button on a Weber grill. Instructions (1) Print the button_housing and button. (2) Cut a piece of 3mm filament to use as the hinge. (3) Drill out filament hole in button if required to get button to…
This is a case that fits a Lamson Remix\Liquid(legacy) fly reel size -5+.
This part mounts to a M70 Samsung monitor to provide a shelf to place a small speaker on. In this case a Bose mini bluetooth speaker. This mounts in place of the Montior stand so is only useful if you have the monitor mounted on a arm and…
These parts will mount a eTopxizu S-360-12 power supply to the right rear of a Sells Mendel. Power Supply: https://www.amazon.com/gp/product/B00D7CWSCG/ref=oh\_aui\_detailpage\_o00\_s00?ie=UTF8&psc=1 You will also need: 3 Pin Power…
This is a travel case for the tooth brush of a Sonicare. There were other cases already available but I wanted one with a threaded cap instead so I modeled this with M24x2 threads on the bottom and cap. I printed in PETG with the cap at…
This will allow for mounting\clamping the 12v 6A power supply from a MPCNC kit to a board\surface. Print 2 and fasten with 2 screws each. In case the power supply varies this worked for a Kastar 12v 6A power brick. Category: 3D Printer…
This bracket can be used to support the rod of a tapestry. Print two or more out, mount, and then tapestry rod will rest in the brackets. Category: Decor
This part screws into a plano bow case and provides a secure storage location for a BeeStinger stabilizer inside the bow case. Category: Sport & Outdoors
This part provides a panel mount for a 4 pin male Molex commonly found at radioshack onto a Mendel. Instructions Connector snaps in from the side with the "B" printed into the surface of the nut plate. Category: Other
This is a wire clip that fits into the Z Axis tube for an MPCNC. It retains the power cables in position on the z-axis for the router. Designed around a Dewalt 660 router. Category: 3D Printer Accessories
This is a hard case for a Lamson Remix\Liquid (legacy version) fly reel spool size -5+.
This is a multi-material case for the iphone 16 pro printed in PETG with a TPU outer cover. There is also a recess in the back to adhere an ESR magsafe ring which can be purchased on amazon. Additionally, there are corner standoffs so…
This will allow for mounting the LCD smart controller module to the front of a Sells Mendel. The supports snap onto the top front M8 rod and then tie bands are used to secure it to the lower one. Two small m3 screws are needed to secure…
These leg extensions press into the hex head on the end of the factory adjustable legs and raise up the cold smoker so it can align with the main smoker cabinet. Category: Other
This bracket will allow you to mount a mechanical endstop switch to the Y Axis motor bracket on a Mendel. Category: Other
This bracket will allow you to mount the Ramps electronics on the left rear of a Mendel. The bracket snaps onto the threaded rods and then zip ties are used to hold it in place. Pockets for nuts allow for the ramps board to be assembled…
This axle is used on the drive wheels for an XV series robotic Vacuum and attaches the wheel to the drive assembly. You will need to find a small sheet metal screw and washer along with this to fully attach the wheel to the drive…
This is a replacement support bracket for a Nordictrack 2750 Pro. This goes on the support strut to lock the treadmill in the folded condition. Category: Replacement Parts
This will allow you to mount a mechanical endstop switch to the x-axis on a Mendel. Instructions Print 2 of these out and clamp them to the X-Axis smooth rods and then mount the mechanical end stop switch. Category: Other
This bracket mounts to a wall and allows the battery to slide on for storage.
This bracket is used to provide a mounting point for wire harness'. In my case it was used on the X axis wiring and extruder carriage wiring on a Sells Mendel. The 3mm hole provides for a point to press in 3mm filament for wire harness…
This case provides additional protection to a Microchip RN370 AAA serial to wifi dongle(same as wisnap AAA dongle). This covers up the dip configuration switches and the momentary button but once configured these aren't really required…
08/13 - Revised Wire inputs (larger and on same face now), adjusted Nano board position to allow for usb connection without removing from mounts. 08/05 - Reduced diameter for circuit board mounting hole ID's slightly. Updated lid rim…
This case provides additional protection to a Bluesnap Smart bluetooth serial adapter module. Adapter: https://serialio.com/product/bluetooth-serial-adapter/bluetooth-adapters-bluetooth-serial-adapter/bluesnap-smart I used a female wifi…
This is a 10mm taller lid for the Gnarly Rambo Archim Case by Allted. I made this because the usb right angle cable I have installed that connects to a Raspberry pi causes interference with the stock lid. Category: 3D Printer Accessories
This allows you to bolt a Makerbot Filament spool holder(thingiverse.com/thing:7105) to the top of the Mendel Z-Rod's. 3/4/2012 - I've experienced some issues with my x-axis missing steps off and on with the spool mounted in the first…
These brackets will allow you to mount a mechanical end stop switch to your Mendel. Instructions (1) Mount mechanical switch to bottom plate (2) Bolt top and bottom plate together loosely (3) Install assembly to Mendel Z Rod smooth bar…
These brackets allow you to mount a 40mm fan to a Mendel. My x,y, and extruder stepper motors were getting quite warm especially during long prints. I turned down the current limit on the pololus after realizing that the Makerbot motors I…
These are all currently available results.
