P
PrintablesMatMake
Nintendo GameBoy Cartridge
To be sure that the print stick to the bed I added a raft
- Downloads
- 1,479
- Likes
- 159
- Rating
- 4.83
All models
Counting matching models…
P
PrintablesMatMake
Tablet stand
Nothing special to say… I print it with 20% infill at 0.2mm layer height but quite sure you can optimize it to print it faster !
- Downloads
- 809
- Likes
- 55
- Rating
- 5
P
PrintablesMatMake
Headphones holder
Headphones holder : You can print the holder with an infill of 20% but you have to setup an infill of approx. 50% for the edge next to the screw pitch (see GCODE file if it's not clear) to increase the strength of the print. Thereby you…
- Downloads
- 535
- Likes
- 39
- Rating
- 4.86
P
PrintablesMatMake
BobbleHead for LEGO
There is no particular recomendation for the print. If you want you can add superglue to reinforce the piece.
- Downloads
- 310
- Likes
- 127
- Rating
- 5
P
PrintablesMatMake
Toad
I draw it really bigger than I print it. I use the scale down function in Cura with 30% as setting.
- Downloads
- 285
- Likes
- 22
- Rating
- 0
P
PrintablesMatMake
Cheating Dice
You have to print the dice without support. I made more than 3000 rolls to establish the statistics.
- Downloads
- 243
- Likes
- 20
- Rating
- 4.25
P
PrintablesMatMake
Nintendo GameBoy Cartridge (label corrected)
Print it on the edge to get a smoother result. To be sure that the print stick to the bed I added a raft.
- Downloads
- 203
- Likes
- 27
- Rating
- 5
P
PrintablesMatMake
Skateboard deck rails
The two main parts are printed in PETG with an infill density of 65% to ensure sufficient hardness and robustness. A tolerance of 0.15mm was added to the letters to fit and hold without anything else. They are printed in PLA with 100%…
- Downloads
- 179
- Likes
- 20
- Rating
- 2
P
PrintablesMatMake
Smartphone stand with passive amplifier for Samsung Galaxy S21/S21 FE
I print the one that is used with the SolidSuit with an adaptive layer height from 0.12 to 0.2mm to save approx. 2h (compared to a full 0.12mm layer height). I only print the stand for smartphone with RhinoShield SolidSuit because I never…
- Downloads
- 177
- Likes
- 23
- Rating
- 5
P
PrintablesMatMake
HyperCube
I print the cube in 0.12mm layer height but if you want save time (approx. 4h) you can print it with 0.2mm layer height but the result will be a bit less clean ! A touch of super glue is needed to build the base…
- Downloads
- 145
- Likes
- 29
- Rating
- 0
P
PrintablesMatMake
Blowable candle
I made the model (the candle) in three parts to facilitate its printing. Because I made the flame in another colour I hade to print it alone. A tolerance has been added to the thread to ensure an easy fit.
- Downloads
- 96
- Likes
- 95
- Rating
- 4
P
PrintablesMatMake
Flexible surgical / COVID mask strap
It's better to print it with PETG because of flexibility but PLA work also ! I print it with 0.2mm layer height
- Downloads
- 58
- Likes
- 5
- Rating
- 0
P
PrintablesMatMake
Foldable surgical / COVID mask strap
I print it with a raft but I think it's possible without if you want to save approx. 10min and 3g of PLA
- Downloads
- 52
- Likes
- 5
- Rating
- 4
These are all currently available results.