Counting matching models…
Use this on the V3 Kirigami bed to get the same Y offset as on the V2 and remove the back/forward wiggle which happens because there is not enough tension on the springs. It can also be used to fix the maximum offset of the V3 by putting…
This is an AMPS mount for carpuride W603 (or W603D). Requires to be mounted from the back!!! You also need: 1 pcs M4 20mm washer (also called wood washer) 1 pcs M4x16mm panhead screw 4 pcs M4 nylock nuts 4 pcs M4x20mm (minimum) screws,…
This is an adapter to use a PINDA probe instead of a BLTouch, while keeping the initial mount for the BLTouch. Basically mimics a BLTouch body and clamps a PINDA in the middle. LJ8 type probes won't work because they are too long, a PINDA…
This bracket is to be used to mount the DCDC 24V to 5V converter to the bottom of the frame, as in the LDO kit instructions. It is thick enough to withstand the weight of the DCDC converter by using just 2 screws, however you can apply…
This is an endcap for a tripod walking stick used by elderly persons, or those who need aid to stand up. It is currently being tested in the wild on metal tripod walking stick. The pipe that goes inside the end cap has 16mm OD and 12.6mm…
This little peg can be used to mount the siboor led bar/pcb on a voron v0 frame. Insert two M3 nuts in top extrusion, use M3x8mm to fasten the mounting peg to the extrusion, use M3x6mm to fasten the PCB to the mounting peg. Bar is mounted…
This is a press and extractor set for the Kawasaki ER6 series of motorcycles. It should work on other bikes with the same engine. Original part number for the seal is 490631055. You will also need: threaded rod M8 140mm in length M8 nuts,…
This will allow you to mount the MTC10 on an AMPS mount (screws down from the device side) It also has a hinge to allow for proper tilting. You will also need: 4 pcs M3x12 screws 4 pcs M3 washer 4 pcs M3 spring washer (grover) 1 pcs M4…
Case for MKS Base board on P3Steel printer. Mounts on the left (as seen from the front) PETG or ABS recommended. OpenSCAD source included Category: 3D Printer Parts
This is an USB blocker with a lip to prevent sliding through the hole. Simple design made with OpenSCAD. Category: Computer
The mud flap on KaThy-M motorbikes has a big hole in it through which mud and debris gets thrown onto the stop light. I made this hole plug to stop it! You will also need some screws, plastic/wood thread with flat cap 3.5mm diameter, one…
Remix of Toolson's release r02 P3Steel X axis parts to be used with the "standard" TR8 antibacklash nut (22mm flange, 12mm spring, 14mm backnut flange). See related things for the full remixed X axis. This thing was made with Tinkercad.…
A part used to mount a signal flasher (mostly) on to a vehicle body (see picture). Use TPU, TPE or other flexible material, keep holes on Z. Category: Replacement Parts
This is just a barrel adapter made for SF1-08xx series bushings. One or more bushings can be inserted in the barrel and used like an LM8UU replacement. I've tested this with 3 SF-0808 inserted and with 2 SF1-0810. Can also take SF1-0812…
Remix of Toolson's release r02 P3Steel X axis parts to be used with the "standard" TR8 antibacklash nut (22mm flange, 12mm spring, 14mm backnut flange). See related things for the full remixed X axis. This thing was made with Tinkercad.…
This is an alternative for centering the top of the Z axis threaded rod tor the P3Steel frame. My frame is from Orballo, and it has a hole on the top for passing the threaded rod through, it is 12mm in diameter. My threaded rod is 5mm. I…
a simple ring to center an AA battery into a 14500 battery hole, used for many flashlights. made with OpenSCAD (source included). print with any material, you need 4 rings. no glue required, should go in smoothly. Category: Electronics
Remix of Toolson's release r02 P3Steel X axis parts to be used with the "standard" TR8 antibacklash nut (22mm flange, 12mm spring, 14mm backnut flange). See related things for the full remixed X axis. This thing was made with Tinkercad.…
This is a case/cover I made to mount my mosfet on the wall of P3Steel printer. This way the electronics are somewhat protected against things. Case made in OpenSCAD, thus it is configurable. Category: 3D Printer Parts
Modified the X axis endstop support in order to better fit the cable harness. The original endstop support is pretty flimsy. This version also works on Orballo P3Steel frame, which is a bit larger than the HTA3D one. All changes made in…
I've mounted a 60mm high torque NEMA17 motor on my P3Steel y axis. However the toolson designed lm8uu clamp hit the back of the motor, which is mounted on the right side as seen from the front. On the y carriage I threaded the left side…
This is modified X-Axis idler to be used on Toolson parts for P3Steel. Instead of the pair of bearings which were used in the original, this one uses a GT20 tooted pulley. Print Settings Printer: Kossel Delta Rafts: No Supports: No…
UPDATE 05 oct 2019: Version 2 now has a two halfs mode, print it twice, put a bushing in the hole and enclose it completely. looks like an LM8UU from the outside. Just a simple adapter. Other things you will need: one SF1 8x10x8…
A bracket for mounting the BTT Relay board on a Voron V0 (or V0.1) 3D printer. Stick it sideways under the bottom panel near the power supply. Tested on a V0.1 might work on V0.2 You will also need: 4 pcs - M3 inserts 4.5x4mm 4 pcs -…
This is an adapter to use a PINDA probe instead of a BLTouch, while keeping the initial mount for the BLTouch. Basically mimics a BLTouch body and clamps a PINDA in the middle. LJ8 type probes won't work because they are too long, a PINDA…
These are all currently available results.
