P
PrintablesNo step design
Grease Tool
Easy print. works great to get to the back rods and keeps grease off your fingers.
- Downloads
- 1,084
- Likes
- 123
- Rating
- 4.9
All models
Counting matching models…
P
PrintablesNo step design
Anycubic ACE Kobra S1 temp sensor
Slides in ACE fits cheap temp sensor. Print with supports.
- Downloads
- 330
- Likes
- 43
- Rating
- 5
P
PrintablesNo step design
Flashforge 5m top handle side hang
Bigger handle and lets you hang the lid from the side when not in use or changing filliment.
- Downloads
- 78
- Likes
- 11
- Rating
- 5
P
PrintablesNo step design
Xacto knife blade box razor craft
Prints with no support. easy handy print.
- Downloads
- 78
- Likes
- 7
- Rating
- 0
P
PrintablesNo step design
Jeep XJ cup holder 1996 and older
Cup and phone holder XJ cherokee made for 1996 back, slips over e-break. It may fit newer cherokee if it does post about it.
- Downloads
- 65
- Likes
- 11
- Rating
- 0
P
PrintablesNo step design
Meshtastic Heltec T114 GPS node case
This case is for sale on Etsy, enjoy but dont sell. Meshtastic Heltec T114 GPS node case holds 3000mah batt and GPS. Chip friction fit in case use 2 3mx4mm screws to secure case buttons print in TPU.
- Downloads
- 61
- Likes
- 9
- Rating
- 0
P
PrintablesNo step design
cat house rodent den
I printed on 220mm bed in current form, took 500 grams. This size is good for a very small cat or kitten Scale it up and show off your cat house.
- Downloads
- 43
- Likes
- 5
- Rating
- 0
P
PrintablesNo step design
Yamaha, Honda, Tohatsu Kill Switch lanyard
Yamaha, Honda, Tohatsu Kill Switch lanyard
- Downloads
- 42
- Likes
- 0
- Rating
- 0
P
PrintablesNo step design
Chicken Chick feeder
Easy print. no supports needed. Great for chicks in the brooder.
- Downloads
- 32
- Likes
- 3
- Rating
- 0
P
PrintablesNo step design
Pet hair brush dog cat grooming
I made this to scrape cat hair off my shirt. Print as it comes in the slicer. MUST PRINT IN PETG. You could use PLA but if you do heat the part before bending. Just bend the ends together and slide the ends in the handle. You could glue…
- Downloads
- 31
- Likes
- 5
- Rating
- 0
P
PrintablesNo step design
Meshtastic Rak WisBlock case 4200mah
I designed this node around a 4200mah battery. The battery spot is 85x40x8. There is a 20x36x10 open spot in the node that can house GPS antenna. I have not tried installing GPS. Let us know and show pics. Battery thickness can be no more…
- Downloads
- 28
- Likes
- 1
- Rating
- 0
P
PrintablesNo step design
Rak WisBlock Meshtastic node case
I sell this case on Etsy and Ebay so please dont sell my design. Rak WisBlock Meshtastic node case 2000mah battery. Basic case hole to access reset button. No room for GPS or sensors. Its a tight fit but it all goes in there. Chip rests…
- Downloads
- 26
- Likes
- 2
- Rating
- 0
P
PrintablesNo step design
Turkey Bookmark thanksgiving
Turkey Bookmark easy print PLA or PETG is fine. thanksgiving
- Downloads
- 23
- Likes
- 2
- Rating
- 0
P
PrintablesNo step design
Baofeng UV5R pocket clip knob protection
Uses orignal screws. protects volume knob. Print on its side, easy print. PLA ok but PETG is better.
- Downloads
- 22
- Likes
- 4
- Rating
- 0
P
PrintablesNo step design
Meshtastic Heltec T114 node case holds 2000mah batt
Avalable in my Etsy shop. Meshtastic Heltec T114 node case holds 2000mah batt. Chip friction fit in case use 2 3mx4mm screws to secure case buttons print in TPU.
- Downloads
- 22
- Likes
- 1
- Rating
- 0
P
PrintablesNo step design
curtains clip blinds blackout
quick easy print. I use petg but pla should be fine.
- Downloads
- 22
- Likes
- 4
- Rating
- 5
P
PrintablesNo step design
comgrow sh01 dryer ptfe grommet
Comgrow sh01 dryer ptfe grommet. This one will test your print settings. Prints in TPU. If your settings are off you can scale it a few %. Pulls through from the inside, PTFE is friction fit just push it in. I printed with .6 nozzle and…
- Downloads
- 20
- Likes
- 1
- Rating
- 0
P
PrintablesNo step design
Tennis ball visor clip
I carry tennis balls in the car and wanted to store them. This holder clips to visor in the car, I test fit in XJ jeep and ford truck. Should fit all car visors.
- Downloads
- 17
- Likes
- 0
- Rating
- 0
These are all currently available results.