Counting matching models…
Wanted to make this model work since it looked so good. Fixed the model to sit flat on the bed and re-cut the socket so the ball will fit since the original model had an error. Also uploaded mirrored versions since this model is not…
The original model was perfect for the 92 base size keys, but the other 18 keys all had additional sizes. Popped off measured and tested all of the other sizes and they all fit and work. Caps was the most tricky, but what Ive got here…
The original model was great, but designed for rear mounted spools. I rotated the Y part about 85 degrees to make this side mounted version. I only converted the Y_Splitter_PC4-M10_V2_rw.stl. Requirements: 3x PC4-M10 pneumatic connector,…
Dummy 13 needed it's own phone to take selfies of it's poses. You'll want to use Tree supports for the hand. Clean them out and a very light brush with a file might be needed. Then the phone should slide right into place. All print…
Wanted to use this model, but it needed a little fixing to make it print right. Print 2, it's symmetric. No supports required.
The last pieces I need to smooth out my whole model was to round out were the shoulders and biceps. The biceps pieces from Smooth were good, but it needed better shoulders. I had to tighten them up, and make them smaller and more fitting.…
Used to use one of these i made for the Fitbit Ionic a while back. Almost made one of these for the Ticwatch, but never ended up sharing it. Finally decided to make one again for the Pixel Watch 2 I just got since I liked the look of the…
Wanted to give my girl a Bunny head option. Couldn't decide which pose I liked better so offer and printed them both. You'll likely want to print as uploaded, with Tree Supports and I also suggest a Brim. I needed one. Note shown is at…
Wanted to try out this head, but it needed to be fixed to fit the 1.0 body.
You'll need to print 2. Mount them fairly wide is best, see photos. Be aware of where the front and back buttons are when sliding them on/off. Make sure you position them far enough away to still allow easy usage of the buttons. No…
Tried to use the original model but was loose and didn't like the finger holes\arcs on it. Took the parts I wanted from the Easy Grip that I've already worked with and thickened them up, made them larger, rebuilt the outside to be smooth…
Wanted a funnel like this that would fit the J-Max's smaller opening without the unnecessary center bits. As a bonus it fits inside of the carrying case with the handle ball inside of the cone (hope that's visible). Its 83mm outside…
The is a slip on rugged case for the Yamaha SEQTRAK. The little groove box has a very long shape so you cannot use a normal folding case design. It's so light and seemingly fragile that I felt it needed something rugged to protect it. It…
Liked the original model but after trying to use it for a week or so noticed it needed an easier way to use the grip holes. Found that fix in the case remix but i still liked the design shape of the original since I already had a case I…
Printed the original than noticed how much of the grill it covered. Didn't like that so found a way to cut it open more while still holding onto the unit safely. The original could be printed without supports, but this one will need them.…
Wanted to try using a TPU stand base instead of the foam rubber strips. Only made it 2mm thick. Might try thicker later but going to give this a try for now. You're free to go thicker in your slicer. 15% infill sounds about right. 2-3…
Made another riser that places the feet at the very back so even when the iPad is tilted all the way back it doesn't overbalance the keyboard and fall backwards even when touched firmly with you fingers. This is based on my previous model…
Tried the original model but realized I wanted more options for height. So I made a version that has slots to support different height riser feet. I provided four options. The lowest should be pretty close to the original. It goes roughly…
Engineered up this shoe brush to attached next to the wheel and let you get mud and goose droppings off your shoes. Print in uploaded orientation with plenty of walls and infill to maximize strength. No supports should be needed. Use an…
Blending my love of Golf and D&D gaming, made these two ball markers. Been using the 3D one for a little while now. It gets some interesting looks. Just made the flat one to blend in better with normal poker chip style markers. I printed…
These are all currently available results.
