Counting matching models…
This is Thrustmaster T.Flight Hotas X for my office chair, easily adaptable for most chairs - just put some foam between chair_clamp_bdy1 and chair_clamp_bdy2 and scew it tight. The elements named right and left are simmetrical except for…
RP2040 + cc1101 in one chassis. The device is working with cc1101-tool firmware from github my fork: https://github.com/McGr3g0r/cc1101-tool my new tool: https://github.com/McGr3g0r/cc1101-wizzard most recent FW+apk:…
If you somehow misplace the sprinkler locking element this part may come handy. The scew is M6 size. Set the infill to 50% Fillament type can be PLA or PETG.
Want to use Geprc GPS M10-DQ or it's variation (22x22mm ) with Speedybee35 ? This is right model for it. Use FLEX materials because the gps must bee pushed into the chassis and there are 4 holders on the edges.
This is chassis for VL53L0X Time of Flight distance sensor for my INAV 6.1 based F450 type drone to use as range finder. Use M4 nut and screw DIN 912 type (imbus) to connect dist_bdy4_top with dist_bdy3_top. Parts dist_bdy1_bottom,…
The switch_mount_bdy_v4.3mf is an mount for switch with other dimensions than the original model.
This 3S battery + bms holder was designed as additonal power supply for my 12V based Near IR flash light presented in other section.
Custom mount for cheap Digoo-MYQ cloud camera Print instructions PLA, 0.2mm layer height setting for speed
Well, this thing required many replacements over time at my house. Although it is not recommendedI to use PLA with water I used PLA with 30% infill. Eventually using PLA may be the reason why I need to replace this thing once per 6 months.
Over a course of few kilometers I lost few of these rubber cups. Now I'm using those printed with PLA, so far 500km passed and still in the place.
Before you print Check your CNC3018-like machine if it fits this design. I know there are many variations of this machine with LMUU10 bearings on Z-axis instead LMUU08 and different bearings spacing. In this project the spacing between…
433 MHz ASK receiver to ESP8266 based WIFI MQTT gateway Print instructions PLA, 40% infill
This is a practical replacement for this weird hinge that breaks very often. Rafts: Doesn't Matter Supports: Yes Resolution: 0.2mm Infill: 50% Filament material: PLA, ASA Notes: remove all supports thoroughly especially in the two holes…
This is another iteration of my cover case for esp8266 development board with 433 ASK receiver or EV1527 receiver. Check OpenMQTTGateway for more info howto interface esp8266 with EV1527 or other 433Mhz based receivers.…
Made upon a request for 606090 Lipo battery support. Never printed, use with caution.
It uses 28byj-48 stepper motor modified to bipolar for use with stepper sticks and arduino. So far it works with arduino stepper board and simple firmware that receives command via serial port. In first step I plan to create custom…
This is Nichia laser holder for my 3018-type CNC machine. There is github project with Kicad schematics and PCB for the laser diode driver based on PT4115 chip. https://github.com/McGr3g0r/pt4115_cnc_laser_driver Caution: thinkering with…
This is DIGOO DG-MYQ camera case designed for outdoor using. Note: this camera model is not intended for outdoor use, however it is fully functional after 3 years of using under the roof of my woodshed The mount arc is 15 degree in…
Print with TPU, use supports. Use at least 2 zip ties on each side. It should fit above the DJI O4. Glue the tinfoil on the back of the gps mount to improve electromagnetic separation from VTX - I have totally no evidence that it really…
Over time your vsett8 will loose some painting due to mud and dirt scraping the footrest. In order to protect it and add more grip I've decided to put a rubber mat on it. Part needed: 3d printed elements for attaching rubber mat to the…
Overloading the plasterboard by the curtain rod actual weight may lead to riping the mounting system off the plasterboard and leave some holes, event if fixed the same spot cannot be reused. This is my practical try of reusing the holes…
Need alternative tripod mount for your tripod ?. The bottom of the square is 30x30mm, total height is 12mm.
These are all currently available results.
![Samyang 800mm motorized focus [WIP]](https://media.printables.com/media/prints/277297/images/2460259_7e04ea58-9819-4a6c-81b5-64c2743a3de5/img_20220822_213447.jpg)
