P
Printableswarpster
Bambu AMS Feeder Button
My remix of the AMS button. I added back the angled part to make it easier to push, still accepts the PTFE tube to protect against wear.
- Downloads
- 3,983
- Likes
- 435
- Rating
- 4.56
All models
Counting matching models…
P
Printableswarpster
Automatic Filament Rewinder (Runs on Marlin)
NOTE:2/1/23 Sorry took so long to get back to this. After a lot of testing I have come to the conclusion that a NEMA 23 stepper with an external driver is the way to go to get the torque needed to wind a full spool reliably. So, I am…
- Downloads
- 1,611
- Likes
- 508
- Rating
- 4.75
P
Printableswarpster
Bambu Lab X1 LED Light frame
This is the final set of files please let me know if you have any issues, Thanks! Note: I have added 8mm to the height of the pedestal, for a total of 20mm, that the AMS foot sits on to give more airflow to the underside of the AMS due to…
- Downloads
- 1,012
- Likes
- 350
- Rating
- 4.91
P
Printableswarpster
Filament Spool Desiccant Holder
A desiccant holder that lives in the center portion of the spool. It will fit spools with a center hole diameter from 53mm and ~64mm and a spool width of 53mm to 69mm. My goal was to fit both the Bambu Lab spools and the eSun spools. It…
- Downloads
- 967
- Likes
- 140
- Rating
- 4.87
P
Printableswarpster
1515 extrusion twist in wire clips
These are just some wire clips for use with the 1515 (15mmx15mm) extrusions. The push into the slot and twist to lock in. Print in ABS or other heat tolerant filament and no supports Category: 3D Printer Parts
- Downloads
- 377
- Likes
- 50
- Rating
- 5
P
Printableswarpster
Eibos Cyclops drive mechanism
The Eibos Cyclops filament dryer has an inherent design problem. Because the heater is directly below the filament spools when the heater heats up to temp it may overheat the filament to the point that the filament fuses to itself. Eibos…
- Downloads
- 352
- Likes
- 124
- Rating
- 4.83
P
Printableswarpster
E3D V6 50mm Blower Fan adapter
This is a 50mm Blower fan adapter, a standard 40mm fan adapter, and a 4010 40mm Blower adapter for the E3D V6 Print without supports in ABS or a filament that will take3 some heat. Category: 3D Printer Parts
- Downloads
- 68
- Likes
- 8
- Rating
- 0
P
Printableswarpster
T-Slot additions for Chinese CNC
These are T-Slot lock slides and knobs for the Chinese built CNC machines that are popular on EBay 6040, 6090 etc. I include a picture of the slots these machines use. These all print without supports and in any material you prefer. I…
- Downloads
- 59
- Likes
- 11
- Rating
- 0
P
Printableswarpster
PanelDue 5i case with usable SD card access
PanelDue 5i case with usable SD card access. Uses 7 M3 4mm x 3mm inserts and M3 bolts (4-18mm and 2 6mm) or longer M3 bolts (4- 22mm and 2 8mm) and nuts. Many people say a 30cm cable is the longest you can use reliably with the SD readers…
- Downloads
- 40
- Likes
- 2
- Rating
- 0
P
Printableswarpster
Railcore II Cable management, Toolboard Enclosure for Hemera.
These are additions I made to my Railcore II printer. Included is a cable management system, a Hemera toolboard.BLTouch mount and Duet Filamant Monitor mount. These are made to mount to the Mandela Rose Works Hemera Mount and Idlers. I…
- Downloads
- 23
- Likes
- 6
- Rating
- 0
P
Printableswarpster
TAMV/TATP tool alignment.
This is a combination tool that serves for TAMV (Tool Alignment with Machine Vision) and ZTATP (Z Tool Align with Touch Plate) tool alignment. There are two models. One for the LM8UU linear bearings and the other for the longer LM8LUU…
- Downloads
- 22
- Likes
- 0
- Rating
- 0
P
Printableswarpster
ControlLeo2 Linear Door Opener Servo
I created this add on Servo Door Opener for my Reflow Oven I built using the ControLeo2 controller. Print in a high temp filament as it will get somewhat hot while reflowing. I used ePC. The only object that needs supports is the Body…
- Downloads
- 22
- Likes
- 4
- Rating
- 0
P
Printableswarpster
Duet Tool Distribution Board model
This is a model of the Duet Tool Distribution Board. The dimensioning is accurate and the parts have been added for looks but the parts are not 100% accurate so don't rely on them. I had to use the diagram of the board on their site for…
- Downloads
- 18
- Likes
- 2
- Rating
- 0
P
Printableswarpster
TAMV_ZTATP combo
This is a combination tool that serves for TAMV (Tool Alignment with Machine Vision) and ZTATP (Z Tool Align with Touch Plate) tool alignment. There are two models. One for the LM8UU linear bearings and the other for the longer LM8LUU…
- Downloads
- 17
- Likes
- 3
- Rating
- 0
P
Printableswarpster
Peopoly Moai Heater Enclosure
This is an add on heater for the Peopoly Moai. It uses inexpensive parts available through Banggood and Amazon . Total cost including the power adapter is about $45. The power supply needs to be able to supply around 8 Amps of power so…
- Downloads
- 15
- Likes
- 1
- Rating
- 0
P
Printableswarpster
Railcore Lower X-Stop Mount
This is a replacement X-stop mount for the Railcore 2 printers. The original mount puts the stop switch actuator almost exactly inline with the hole in the Aluminum X Carraige (not sure on the printed one). Any skew at all to the mount…
- Downloads
- 11
- Likes
- 1
- Rating
- 5
P
Printableswarpster
Railcore magnetic door latch
This is a magnetic latch for a railcore. It uses 4 qty - 1/2" (12.7mm) X .063" (1.6mm) magnets from Home Depot encased in plastic covers to minimize the magnetic force. The stationary part holds 2 magnets and then screws down into the…
- Downloads
- 10
- Likes
- 2
- Rating
- 0
P
Printableswarpster
Railcore Wire Cover
Just a simple wire cover for the Railcore printer. Thiis was designed around the BondTech printed mount and will clear a BLTouch. You will need to drill out the top and bottom inside Wire tie square holes with a 4mm bit. I designed it to…
- Downloads
- 9
- Likes
- 1
- Rating
- 0
P
Printableswarpster
Railcore top lid support clip
These are "lid supports" for the top lid of the Railcore top made by Mandala Rose Works.. They get mounted on the side extrusions of the Top Enclosure and give a little extra support for the middle of the lid. They are in two pieces.…
- Downloads
- 8
- Likes
- 1
- Rating
- 0
P
Printableswarpster
Hemera Filament Sensor Mount for Railcore
This is a mount for the Duet Magnetic filament monitor for the Hemera on a Railcore. The STLs are oriented for proper printing and should not require supports. Where supports are needed I added an integral supports (2) that need to be…
- Downloads
- 8
- Likes
- 1
- Rating
- 0
P
Printableswarpster
Peopoly MOAI LED Lights
This is a set of files for adding interior LED lights to your MOAI printer. It includes 4 corner lights and a center light that operates only when the door is opened. The corner lights turn on independent of the printer or door. I mounted…
- Downloads
- 5
- Likes
- 0
- Rating
- 0
These are all currently available results.