Counting matching models…
A collection of mounts for various Aqara sensors. Will grow as I get more stuff. Prints solid, no supports, large surface down (lock ring upside down). Can barely see them if printed in white. Mounts will work with or without tape…
A stand for the 12V Bosch Battery, and bit holder for the GSR 12V-15 FC drill. The bit holder may fit other Bosch drills if they have the same rubber band it attaches to. Apparently the bit holder also fits the Bosch GSR 12V-20 brushless…
If you don't see a gif animation here, then something broke, or you are blocking it. Turntable is 33cm. Photo 4 shows pretty well how bright the default top with the 17cm LED COB is. If you make one, consider uploading a picture. It's…
Simple wall mounts for the Sonoff Zigbee 3.0 USB Dongle Plus and Plus-E. For use with home automation gear. Prints solid. Back side down. No supports. Dongle slides in from the end. lul.. Has space for a USB extension cable. Can be…
This is a removable adapter that makes it possible to use Makita batteries on Ryobi tools. It is built on my other Makita battery barrel jack adapter. This was made because Makita does not make a cordless glue gun, and I have no interest…
A quick project which is a replacement for Beyer's shitty plastic side brackets that attaches the speakers to the aluminum forks. I've had two sets of these break over the years, on two headphones. The plastic crumbles over time and snaps…
If you have ever looked for a silicone wire set, you may have seen the type that comes in a cardboard box on sites like eBay or Amazon. They usually come with 5 or 6 spools. The cardboard box they come in is supposed to work like a…
--------------------------------------------------------------------------------------------------------- Clock running WLED above. No, you don't need a large printer to make this. It's split into 6 segments. In fact - it should be…
-------------------------------------------------------------------------------------------------------- These are the current mounts: Horizontal: 5,10,15,20,25,30,35,40,45 Vertical: 5,10,15,20 Dual: 5 Vertical, 10 Horizontal Dual: 5…
A simple wall mount for the Home Assistant SkyConnect - A Zigbee\Matter\Thread radio adapter used in home automation. Prints solid. USB side down. Is attached with double-sided tape. Can be screwed in with the hole. Fits with the included…
This is a cap for the Samsung Fit Plus USB flash drives. It does not come with a cap so I had to make one because the sharp corners of the USB plug could poke a hole in my hardshell jacket if I put it on my keychain. And with the side…
Features: No programming or uploading anything, just connecting wires. 16 bearings (13 on 18cm version). Remote controlled. On\off switch (on remote and table). Reversible direction (with remote). Adjustable speed (on USB board). Battery…
This is the second model in my segmented light series. Here I wanted to combine a lamp and a bowl. It's mostly intended for decorative use but it does put out a decent amount of light (up to 24 watts in my case). Use it to hold everyday…
This is a 70 watt "7000" lumen dimmable LED floodlight that mounts on anything that has a 1/4" or 3/8" thread. It's a standard thread used on all kinds of camera gear, like tripods, microphone stands, articulating arms, etc. Also has a…
-------------------------------------------------------------------------------------------------------- Runs on USB-C (5v on everything) 45mm diameter. 30mm tall All parts prints solid Should be PETG or better, due to LED heat Base…
Warning: If you make this, you will be sticking diy electronics into expensive cameras. If you fry something, that's on you. Not a recommended project unless you are familiar with the components used. Make this at your own risk. Canon…
The Meshify 2 case from Fractal does not have a lot of vent holes in the inside bottom of the case (under the GPU). Half of them are pretty much blocked by the powersupply. If you are using fans to suck air in from the bottom, then a lot…
A simple stand for the Sony SRS-XB41 mobile speaker. I made this a long time ago, might as well upload it. Printing it is pretty straightforward. It should have a high layer count, otherwise you might get holes inside of the bottom. There…
This is a stand for my **70 Watt worklight.** It's designed to take Makita batteries, but making an adapter plate for other 18V batteries like Dewalt, Milwaukee, Bosch etc. - is possible. A fusion file is available for a blank plate so…
Since I could not find my shitty phone holder from eBay, I had to make my own, and here it is. It's pretty simple and fast to use. I don't like all-plastic models that much, so it does require springs, a threaded 1/4" brass insert…
A warning first: This project involves using lithium ion pouch cells, which is one of the most dangerous types of batteries available. They are easy to physically damage with anything sharp or pointy. If the bag is pierced it will most…
These are two custom bodies for the Aqara door sensor PCB (for home automation). One that enables the use of external triggers like limitswitches, buttons, wires, and anything that makes a connection really. The other one has a built-in…
I don't know why Aqara made a modern Zigbee switch in a way where It looks like it was designed 20 years ago. The "white" color looks like it's been sitting in the sun for too long, turning it almost beige. Mushy buttons make creaky…
This is a solar enclosure for the Soshine 6w solar panel. It is designed for Meshtastic but can be used for any project that can run on a 6 watt panel (like MeshCore). It will be waterproof if properly sealed. The pole photo is outdated.…
This uses an optional lithium polymer battery. These are fragile so handle it with care. If it's punctured, it will catch fire. Use at your own risk. Do not buy a battery without a protection board. The converter does not have any. Since…
A 3-channel voltage and current sensor for Home Assistant using ESPHome. Could for example be used as a battery or solar panel tester that will graph everything out in HA. Basically 6 multimeters in one unit. Can also be used standalone…
A simple wall mount for the Woox R7051 Zigbee siren. For use with home automation software like Home Assistant. Prints solid, backside down. No supports. Is taped to wall with double-sided tape. Has holes for cables and buttons. If you…
These are 3 mounts for some ACASIS USB hub's with up to 30\45\90 degree angles. You will need 2x 12mm M3 screws and nuts for each side. Screws can be longer as they go all the way through. Should use washers to get better sliding and the…
A simple wall mount for the Athom AR01V3 IR\RF (433Mhz) Transceiver (might also work for the AR01 IR-only unit). I use this with Home Assistant's new Infrared\RF system, which allows you to automate things that use this technology, like…
These are all currently available results.
