Counting matching models…
After trying a few generic online models I designed a holder that would work with newer iPads that are 6mm thick. So far I've been using it without gluing any parts together, they are snug enough to hold it, although a bit of sticky…
Learning F360 and made this stem mount for my garmin GPS. It's shown with a garmin insert, but if you search for “garmin k-edge” you can find a printable one. The screws just self tap into the mount, although you could use longer ones…
I wanted a stand that was compact enough to easily take mountain biking that could hold the phone up for taking group shots. This was also an excuse to try modeling in Shapr3D on the iPad. Designed to take a flat head M3x12mm screw for…
I needed a few changes to the original: tapered pipe protrusion and a way to offset an "endstop" from the corner. I'm pretty new to OpenSCAD so there's probably room for improvement, but it was a fun learning process. The protrusion is…
The kid wanted a "cool" charger for his watch and while I was at it I made one for my wife. Print instructions I found the base models on minifactory by Mariusz Leśniak ( https://www.myminifactory.com/users/Lesiu ), scaled them up and…
Arachne wall generator, tree slim support, and brim for the cups works for me on Bambulab X1. Collar doesn't need anything special. All printed w/0.20mm standard.
Prints without supports although if your printer has issues with overhangs on openings a small bit might help. Most coat zipper pulls I measured are around 12mm wide and 2mm thick, so this is modeled for that approximate size. May take a…
Wanted to try a multi-color ring that wasn't just a stripe while I'm learning F360. Depending on color chosen it will be more or less of a subtle highlight. Print at 0.10mm, with color change at 1.5 and 1.7, unless you scale it. This ends…
Getting gravel bike ready for season I noticed a bunch of the little rubbery plugs that seal the M5 mounting points were missing. The originals are an ok design, but the material is more flexible and they tend to loosen. So I made…
The original “halves” just had too many issues: connectivity tolerances and the hinge “ears” were on layer lines and weaker. So I merged it and it printed really nicely without supports, at least on my MK3 w/prusaslicer.
Simple part whipped together with tinkercad to provide another mount point for shower head. In this case the “slot” tapers from 22-24mm and the handle was around 25-27mm. I printed with 3 perimeters and 15% gyroid using PETG
Winter comes and we put electric blanket/mattress pad on the bed. They say not to run electrical cable between mattress and box frame, so this is a quick print holds the cable out of the way. For this the cable is 11mm x 2.5mm. No…
Modded input shaft to accept screws with larger heads, also separated shaft so it can print without supports
Slides into strap and has bottom wedge to help keep it from slipping out, also the bottom is sized so the varia has support down there as well as with connector. I used a bent section of coat hanger to make a safety clip to further keep…
Sometimes we have a remote employee facetime into a meeting and need a secure way to mount the device. Push pins sort of work, but I figured I could whip together something a bit more secure and universal. The base just slips between the…
The old rubber-ish handle got warped and weakened over the years but the metal will probably last forever. So I whipped up a replacement for it. Printed in PETG, a little cleanup of the threads probably necessary.
Friend's ebike charge port cover broke off the thin rubber tether (common issue) and he was worried the whole thing would fall off without the tether. This is a smaller cap that slides into the port to keep dust out. Printed in TPU for…
I 3d printed a panel to put inside bike bag to firm the mount when it is screwed to bike frame. The main problem is needing tools and messing around with lining everything up. Some bike manufacturers include thumb screws so I made this…
These are all currently available results.
