P
PrintablesMike
21700 Support 2x10
A support for 2x10 arrangement of 21700
- Downloads
- 215
- Likes
- 14
- Rating
- 0
All models
Counting matching models…
P
PrintablesMike
21700 Spacer for Onewheel Battery Pack
This spacer is used to set the horizontal spacing of 21700 cells so that the height of the pack fits within a onewheel XR battery enclosure.
- Downloads
- 191
- Likes
- 20
- Rating
- 0
P
PrintablesMike
21700 secondary spacer for onewheel battery pack
A special spacer is used to set the horizontal spacing of 21700 cells so that the height of the pack fits within a onewheel XR battery enclosure. This secondary spacer allows the addition of more than 15 cells.
- Downloads
- 77
- Likes
- 6
- Rating
- 0
P
PrintablesMike
Onewheel XR Battery Box with o-ring
A onewheel XR battery box with o-ring seal and top port. Top port is designed to work with an access box on the top of the rear foot pad. O-ring is .07" cord stock. Plate is designed to be 1/16" aluminum 6061 and should be bonded to the…
- Downloads
- 65
- Likes
- 12
- Rating
- 0
P
PrintablesMike
Tilted Controller Box for WTF +XR Onewheel
This mod replaces the stock controller box. The heat sink is tilted 4 degrees to account for the aftermarket WTF rails.
- Downloads
- 53
- Likes
- 11
- Rating
- 0
P
PrintablesMike
Drok DC-DC Boost Charger
This is a case for the Drok Digital Step Up Volt Regulator DC 8V-60V to DC 10V-120V 15A 900W Numerical Control Boost Converter Automate Power Supply Module . I use this to charge my electric skateboard from a battery bank or DC power…
- Downloads
- 39
- Likes
- 3
- Rating
- 0
P
PrintablesMike
Auxilliary Battery Box for Stock Onewheel +XR Battery
Many people replace their stock onewheel +XR battery with an aftermarket battery. This enclosure is designed to house the stock battery to keep it safe if you want to reuse it for other purposes. It uses 4-40 screws and heat inserts. It…
- Downloads
- 36
- Likes
- 6
- Rating
- 0
P
PrintablesMike
Onewheel Footpad with Switches
This design is what I ride instead of the typical onewheel footpad that uses a force sensing membrane. Instead this design uses two small IP67 switches . The button is held in place above the switch by the seal, which is 1/32" EPDM (not…
- Downloads
- 28
- Likes
- 6
- Rating
- 0
P
PrintablesMike
Onewheel Rear Footpad V2
Updated rear footpad designed to have thicker walls. Added more fasteners to the front edge to increase stiffness. Made full length version.
- Downloads
- 27
- Likes
- 7
- Rating
- 0
P
PrintablesMike
Floatwheel Fender
A Floatwheel fender that allows for maximum tire clearance to fit tires like the Burris 11.5x7x6. Use any material you like for the shield. Polycarbonate and polyethylene are good choices. 1/8" thick should be sufficient. 8" wide. 17"…
- Downloads
- 26
- Likes
- 3
- Rating
- 0
P
PrintablesMike
Little Focer 3.1 Enclosure Concept 6.0
This is a custom enclosure for the little focer 3.1 and onewheel rails. This also works with WTF rails. This build requires you to make a custom heat sink. This build is designed for a custom footpad. -Replaces charge port with XT90E-M…
- Downloads
- 22
- Likes
- 4
- Rating
- 0
P
PrintablesMike
High Voltage Antispark XT90 Loop Key
This small print fits on the end of a normal XT90F loop key to make it an anti-spark with a stronger resistor than the XT90S. The resistor within the print should be less than or equal to .1" dia x .25" length.
- Downloads
- 22
- Likes
- 2
- Rating
- 0
P
PrintablesMike
Custom Onewheel Rear Footpad
Printed in ABS as halves and glued together with acetone. Designed to sit on top of a formed 0.09" aluminum 6061 sheet. I am 150 lb so I recommend 1/8" or thicker if you weigh more. Hardware should be the same as the Kush Hi but you will…
- Downloads
- 20
- Likes
- 7
- Rating
- 0
P
PrintablesMike
XT-60 Auto-Lid/Cap
This model uses a torsion spring to automatically cap an exposed XT-60 connector when disconnected. Use the following spring or similar: https://www.mcmaster.com/9271K875/ Put two 90 degree bends in the spring and clip the ends as needed…
- Downloads
- 12
- Likes
- 1
- Rating
- 0
P
PrintablesMike
Rear Footpad V3
A rear footpad for the Onewheel XR platform. Works great in wet, muddy, or icey conditions with a treaded shoe. If you make your own base plate I suggest minimum 0.09" aluminum plate. If you want to buy the base plate I think this is a…
- Downloads
- 12
- Likes
- 1
- Rating
- 0
P
PrintablesMike
Foot Binding Force Release
Print this with 100% concentric infill. I found ABS/ASA to work the best. PETG failed prematurely. Uses #10-32 hardware or similar.
- Downloads
- 8
- Likes
- 0
- Rating
- 0
These are all currently available results.