P
PrintablesMagnatic Design
Labyrinth cylinder
Print with 0.2mm layers.
- Downloads
- 1,676
- Likes
- 158
- Rating
- 4.71
All models
Counting matching models…
P
PrintablesMagnatic Design
Whiteboard marker holder
A simple whiteboard marker holder for four markers with recesses for small magnets (10mm diameter, 2mm depth). You will need 6 magnets and have to print the model twice. Print Settings Printer Brand: Anycubic Printer: Semi-closed 4Max…
- Downloads
- 470
- Likes
- 44
- Rating
- 4.85
P
PrintablesMagnatic Design
Decorative pot - Wicker
Layer height: 0.2mm See here for a photo of the planter with a small cactus.
- Downloads
- 227
- Likes
- 53
- Rating
- 5
P
PrintablesMagnatic Design
Decorative pot - Braids
Layerheight: 0.2mm See here for a photo of the planter with a small cactus.
- Downloads
- 170
- Likes
- 34
- Rating
- 0
P
PrintablesMagnatic Design
Treasure chest
Layer height: 0.2mm Remove edges after printing.
- Downloads
- 99
- Likes
- 8
- Rating
- 5
P
PrintablesMagnatic Design
Line art portait of a cat in a frame
Print at 0.2mm layer height. The base plate is 1.4mm heigh. So start your colorswitch above that. Coloring the eyes has a really nice effect. I did this in the base plate. The picture has a brim firmly attached to prevent warping. Cut it…
- Downloads
- 56
- Likes
- 12
- Rating
- 5
P
PrintablesMagnatic Design
Lens cap Panasonic Lumix FZ82
This is a replacement for the flimsy lens cap that came with the camera and that keeps falling off. This lens cap clamps onto the outer rim of the lens. It has room for the lens to extend if you accidentally switch on the camera with the…
- Downloads
- 46
- Likes
- 6
- Rating
- 0
P
PrintablesMagnatic Design
Stand for decorative pots
Layer height: 0.3mm Remove edges from plank after printing. Use small screws (length < 10mm, +- 1.5mm diameter) to attach planks to stand at the underside of the planks.
- Downloads
- 42
- Likes
- 20
- Rating
- 0
P
PrintablesMagnatic Design
Small vault
This is small vault with 120 x 120 x 120 mm outer dimensions. There is a holder for an ESP8266 (D1 mini) that drives a small servo (SG90) which moves the wiper. The wiper pushes a big bolt (M12, length appox. 47mm) up to lock the vault.…
- Downloads
- 35
- Likes
- 11
- Rating
- 0
P
PrintablesMagnatic Design
Decorative pot - Basic Polygons
Layer height: 0.2mm See here for a photo with a small cactus.
- Downloads
- 27
- Likes
- 4
- Rating
- 0
P
PrintablesMagnatic Design
Remarkable Pro ruler
A simple ruler to draw straight lines on a Remarkable Pro. It snaps onto the ridges on the side of the paper tablet. Print it in PETG to prevent scratches on the screen. You can park it on the blank space at the bottom of the device.
- Downloads
- 24
- Likes
- 3
- Rating
- 0
P
PrintablesMagnatic Design
Compaq Portable III keyboard stand
The keyboard stands from my Compaq Portable III were both broken. This is the replacement part.
- Downloads
- 24
- Likes
- 0
- Rating
- 0
P
PrintablesMagnatic Design
Decorative pot - Mystic Script
Layer height: 0.2mm See here for a photo of the planter with a small cactus.
- Downloads
- 21
- Likes
- 1
- Rating
- 0
P
PrintablesMagnatic Design
ETH02 case
This is a simple case for the ETH02 ethernet relay. Print Settings Rafts: No Supports: No Resolution: 0.2mm layer height Infill: 15% Category: Electronics
- Downloads
- 17
- Likes
- 1
- Rating
- 4
P
PrintablesMagnatic Design
Philips Sarista Bean Funnel Stirrer Axle
This is a replacement for the standard axle of the bean stirrer in a Sarista bean funnel. The original one "expires" after about one and a half funnels of beans. When you replace that one with this, the bean funnel can be refilled…
- Downloads
- 13
- Likes
- 0
- Rating
- 0
P
PrintablesMagnatic Design
Waveshare Jetracer rear axle / wheel attachment replacement
My Waveshare Jetracer AI kit came with mismatching motor-axles (too big) and wheel-axle-attachments (too small) for the rear axle. This is a functional replacement part.
- Downloads
- 13
- Likes
- 1
- Rating
- 0
P
PrintablesMagnatic Design
Couch raising thing
I made this thing to raise my couch just a few centimeters (4 cm). By using just two of them at the front the effect is that the couch is tilted back a little. Print Settings Rafts: No Supports: No Resolution: 0.3mm layer height Infill:…
- Downloads
- 7
- Likes
- 1
- Rating
- 0
These are all currently available results.