Counting matching models…
A small fake book with storage inside for trinkets and valuables. The hinged book cover prints in place, print the pages then glue into the cover. you can also add an 8mmx2mm magnet to secure the book closed.
I needed a scoop for some powder detergent, couldn't find one I liked so designed my own. Prints without support in the orientation shown on the print bed picture. I used PETG and it's holding up nicely. Thanks to some lovely printers…
Sylvanian Families Wardrobe. I printed this in PLA. Print the main body on its back facing up, supports are needed for the inside top section. Print the doors flat on their back facing up, no support needed. Once printed the doors pop in…
A simple to print book stand. Can be enlarged to maximum bed size of a MK3/MK4 to accommodate larger books.
I made this as my kids had lots of characters but only one bed. prints in 4 pieces then either pushes together or you can glue in place depending on how your print tolerances come out. Printed on MK3s+ at 0.2 layer
Sylvanian Families Piano. I printed this in PLA. Print the main body on its back and it won't need supports. The lid prints flat and glues to the main body. the keyboard keys print flat, I did 3 colour changes to achieve the 3 different…
Kids toy train designed to carry soft toys around. Prints without support and 608Z bearings press into each wheel and onto the chassis. Print the engine and 4 wheels, then as many carriages as needed.
I printed this in PLA with support on build plate only. Just attach a balloon to the spout and inflate it by blowing in the outlet at the back.
Barbie bookshelf & books. I printed these in PLA. The bookshelf printed flat on its back with no support. The open books, inner and outer print standing up then can be glued together. the closed books outer prints standing up and inner…
Printed at 0.3mm layer height on a MK3s and MMU2 with 3DQF PLA filament. I used support on build plate just for the fixings on the back but probably not necessary.
Cookie cutter and stamps to make cookies as seen in Squid Game on Netflix.
A selection of spacers that can be used to straighten out warped beds. I needed these for my Kobra Max 400x400 bed. I printed them in Yellow PLA (cos they remind me of PacMan)
Sylvanian Families microphone & stand. I printed the microphone standing up with a colour change. The stand prints in 3 pieces. the pole glues into the base. the microphone holder is attached to the pole with a piece of 1.75mm filament…
A fun little print my kids asked me to make. Print the main body then glue short pieces of flexible filament in the holes for the bristles.
Batman logo extruder spinner/visualiser. Glue a a magnet to the rear and add to your extruder motor.
Multi colour Yoshi with holes for 8x2mm magnets. Printed on MK3s+ & MMU3 at 0.2 layer
Punisher logo extruder spinner/visualiser. Glue a magnet to the rear and add to your extruder motor.
Printed on a MK3s with MMU2 in 3DQF PLA filament.
A simple mount for the Logitech C270 webcam. Prints face down and mounts with countersunk head screws. I have it fixed with just one screw so I can spin the camera to my desired position.
I made these to replace the flimsy ones that came with an awning. They are printed in Prusa PETG with 6 vertical shells and 40% infill, and can withstand being hammered into fairly hard ground.
The mount can be attached to the base to lift the camera up high enough to use it to monitor prints on a MK2/3/4. Or the mount can be screwed to a ceiling or under a shelf to invert the camera, like a security camera.
Viking longboat toy. My kids wanted this for their Sylvanian families toys to take to the seas. Printed the main boat body with supports and then printed and glued the rest. I printed this on an XL. If you are using a smaller bed you will…
Some fun frames for my kids instant camera. Printed upright with support enabled. I added double sided tape so they can be mounted to the wall/furniture.
A Percy themed cake decoration. Designed to sit at the edge of the cake so it looks like Percy is emerging from a cake tunnel. This was a request that I enjoyed making so I thought I would upload it here. Printed in PLA on a MK3.5s with…
I needed a bracket for some ducting some modelled these. One is 12.5 and the other 94mm. There is a slot inside to slide a cable tie through to fasten the duct to the bracket. Printed in PETG on an XL.
This model consists of several parts you can print separately and glue together. The hinged storage book prints in place standing up. With a 0.4mm nozzle the print in place hinge works great. You can also use two 8x2mm magnets to keep the…
I needed some dampers for an extract fan so modelled these. PETG top and bottom with a TPU section in the middle. There are two version, one thin light duty and one thicker heavy duty. I added a washer for fastening the base and M5 screws…
Judge Dredd badge extruder spinner/visualiser. Glue a magnet to the rear and add to your extruder motor. I printed this in PLA with a MK3s+ and MMU3.
Multi colour Jasmine with holes for 8x2mm magnets. Printed on MK3s+ & MMU3 at 0.2 layer
These are all currently available results.
