P
PrintablesBlack-Villain
Poulan/Husqvarna Fuel Tank Grommet (574678001)
Print in TPU or similar for flexibility and fuel resistance, also recommend using some gasket maker/RTV to be safe.
- Downloads
- 100
- Likes
- 8
- Rating
- 5
All models
Counting matching models…
P
PrintablesBlack-Villain
XJS Throttle/Accelerator Bushing (C34388)
This is a replacement Throttle/Accelerator Linkage bushing for the Jaguar XJS, but should also fit the XJ12. Tested this on my 88 XJS and it works beautifully. Print in TPU or similar flexible if at all possible . Included are two files…
- Downloads
- 56
- Likes
- 3
- Rating
- 5
P
PrintablesBlack-Villain
Jaguar/Leyland Battery Terminal Cover
(Print in TPU or other Flexible) This is a positive terminal cover for some 70s-80s British Leyland (Jaguar) Vehicles. This is not the one for the late-80s XJS with the 90-degree battery terminals, these are for the standard straight…
- Downloads
- 49
- Likes
- 8
- Rating
- 0
P
PrintablesBlack-Villain
Z31 300ZX Blanking Plates (88 300ZX)
These are the plates to blank off the IACV, EGR, and Cold Start Valve on a Z31. These were designed and tested from an 88 300ZX Turbo, unknown if it fits other years or naturally aspirated cars, so do your own research. Print in PETG or…
- Downloads
- 41
- Likes
- 3
- Rating
- 0
P
PrintablesBlack-Villain
Jaguar X300 XJ6 Fuel Pump Mount (NNA6025BA)
I'm adding fuzzy skin to the "required" list, it helps immensely with PETG. Unknown for TPU but I assume it's the same. This is a replacement for the rubber fuel pump mounts/collars for the Jaguar X300 (XJ6/XJ12/XJR). As I recently found…
- Downloads
- 39
- Likes
- 6
- Rating
- 0
P
PrintablesBlack-Villain
Z31 AIV Plugs
The AIV is the Air Induction Valve that sits behind the driver's side headlight on the Z31. These two plugs are to plug the holes left behind on the intake boot, and to plug the line coming off of the AIV (the hose that comes off of the…
- Downloads
- 37
- Likes
- 7
- Rating
- 0
P
PrintablesBlack-Villain
Jaguar XJS/XJ12/V12 PCV Breather Hose (C44386)
PRINT IN TPU SO IT'S FLEXIBLE AND OIL/GAS RESISTANT This is a replacement elbow for the PCV/Breather on a Jaguar V12, P/N#C44386 I made the top of the elbow flat enough that it can be printed upside down, no supports necessary. Might have…
- Downloads
- 31
- Likes
- 4
- Rating
- 0
P
PrintablesBlack-Villain
88-89 Z31 300ZX Tension Rod Bushing
This is a replacement Tension Rod Bushing for the 88-89 Z31 300ZX. The 88-89 Z31's are different than other years and it's much harder/more expensive to source bushings. This is based off of my measurements of a poly replacement bushing…
- Downloads
- 25
- Likes
- 4
- Rating
- 0
P
PrintablesBlack-Villain
Anti-Whistle Inserts for HAUL-MASTER Cross Bars 64877
These strips are designed to eliminate the wind noise/whistling on the Harbor Freight Haul-Master Cross Bars. I designed them to be a fairly snug/flush fit (to eliminate rattling), so I'd recommend printing the small test piece file to…
- Downloads
- 21
- Likes
- 3
- Rating
- 0
P
PrintablesBlack-Villain
Jaguar X-Type Airbox Mounts
These are replacement mounts for the Jaguar X-Type (X400) airbox, for use on 2.5 and 3.0 vehicles. Untested on 2.1, and I'm in the US so no diesels either. Print in TPU. The lower mount isn't an exact copy of the original, I didn't have…
- Downloads
- 20
- Likes
- 4
- Rating
- 0
P
PrintablesBlack-Villain
Bosch EV1 Pintle Cap Tool
Use this to install new pintle caps on the injectors. It protects the pintle cap, and has a hole in the middle so you don't accidentally hit the end of the injector. Just slip the new pintle cap onto the end of the injector, slide the…
- Downloads
- 17
- Likes
- 2
- Rating
- 0
P
PrintablesBlack-Villain
Jaguar XJS Mustang TPS Sensor Mount
I've modified the design compared to the first iteration that I installed on my car, so this should work fine, but I'm including the STEP file if it needs modified, since I don't want to go through the trouble of printing another and…
- Downloads
- 16
- Likes
- 2
- Rating
- 0
P
PrintablesBlack-Villain
Stand for Harbor Freight/Thunderbolt 1.5W Solar Battery Maintainer
This is a stand for the Harbor Freight solar battery maintainer, to keep it up at an angle. I have it set at 30.5° SKU 64251 Only one file included, orient upright, and mirror to get the stand for the opposite side.
- Downloads
- 14
- Likes
- 2
- Rating
- 0
P
PrintablesBlack-Villain
Jaguar XJS AAV Plug
This is a plug to block off the AAV inlet on the Jag V12. I'm sure we all know how troublesome the AAV is on these cars, it's failed on every single one I've bought... so here's my solution. I don't know the long-term effects of blocking…
- Downloads
- 12
- Likes
- 1
- Rating
- 0
P
PrintablesBlack-Villain
Jaguar Series XJ12 Fuel Pump Adapter
This takes the old-style Lucas pump with the side outlet and allows you to install the newer-style and easier to get inline pump (i.e. from an HE XJS or similar) into the stock mounting bracket. Print two, in some kinda flexible filament…
- Downloads
- 11
- Likes
- 1
- Rating
- 0
P
PrintablesBlack-Villain
Hamilton Beach 40DM Parts
These are some replacement parts for the Hamilton Beach 40DM Malt/Milkshake Mixer Screw Spacer: The 2 screws that hold the top/motor cover originally had what looked like 2 O-Rings or lock washers, either way they crumbled as soon as I…
- Downloads
- 10
- Likes
- 0
- Rating
- 0
P
PrintablesBlack-Villain
05+ Cadillac STS Intake Plug
This is an intake plug for where the PCV connects to the intake tube on the 4.6 05+ Cadillac STS. My hose shattered and this is a temporary solution so there isn't just a vacuum leak after the MAF in the intake. I printed it in TPU so it…
- Downloads
- 7
- Likes
- 3
- Rating
- 0
P
PrintablesBlack-Villain
Jaguar X300 Transmission Mount MMC7553AA
This is a replacement for MMC7553AA. The originals are foam and are 99% likely completely disintegrated by this point. Although the foam no doubt provides better NVH characteristics, TPU should do the job fine and it's better than having…
- Downloads
- 0
- Likes
- 0
- Rating
- 0
P
PrintablesBlack-Villain
Jaguar Radiator Mounting Pad/Bushing
P/N# CCC4794 Replacement for the Radiator mounts for a Jaguar XJS, XJ6, XJ12, etc. Haven't printed these myself to test them (mine were in good shape), but they're dimensionally identical to the OEM ones so they should work fine. Print in…
- Downloads
- 0
- Likes
- 0
- Rating
- 0
These are all currently available results.