Counting matching models…
I found the original difficult to print as the logo was protruding so it could not be printed with the top of the lid face down. I wasn't particularly bothered about the design so I removed it. There is also an alternative design which is…
A remix of https://www.thingiverse.com/thing:2188344 which has been filled in so that it can be printed flat without requiring supports. This makes it much easier to print in TPU. I have also scaled it to fit a standard UK 44mm bath drain…
A dust cap for a PL259 UHF plug Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 0.2mm Infill: 25% Filament: Enotepad TPU Red Notes: The outer barrel of different PL259 plugs might vary slightly…
Desk stand bracket to hold the facia panel of the Yaesu FTM-100D at a 45 degree angle Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 0.2 Infill: 10% Filament: Sunlu PLA+ Black Category: Other
The sealant cartridge nozzle cap at https://www.thingiverse.com/thing:3375441 is designed to be used with an o-ring. This is an alternative which can be printed in TPU Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No…
This is a plug to seal up a 2" overflow hole in a bath tub. It can also be loaded into tinkercad and modified if you wish to modify the end to attach an overflow pipe as a lot of fittings require a 1.5" hole. I have also included just the…
When removing a washing machine you are left with the drain hose connector in the waste pipe not connected to anything. Water can leak out depending on the type and at the very least it can cause smells to escape. This is a plug which…
A power plug for a Motorola MC Micro radio Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 0.2mm Infill: 25% Filament: Generic PLA Notes: Printed using 1.2mm wall thickness Custom Section…
Case for the Anderson Powerpole distribution unit with over voltage and reverse polarity protection. Full details are available at https://github.com/RADARC/Powerpole-distribution Print Settings Printer Brand: Creality Printer: Ender 3…
A simple plug for a water trough. Tapered from 32 to 44mm in diameter Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 0.16mm Infill: 10% Filament: Enotepad TPU Category: Outdoor & Garden
An adaptor for a Motorola MC Micro to enable a speaker to be connected via a phono plug. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: Yes Supports: No Resolution: 0.2mm Infill: 20% Filament: Generic PLA n/a Notes: Raft…
Replacement O-Ring for the hinari Genie Blender Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 0.16mm Filament: Enotepad TPU Notes: Designed to be a tight fit ideally printed with a TPU with a…
Customized version of https://www.thingiverse.com/thing:270130 Created with Customizer! https://www.thingiverse.com/apps/customizer/run?thing_id=270130 Instructions Using the following options: number_of_sides = 14 vase_height = 100…
A funnel for the Wagner sprayer bottle to avoid spilling paint when pouring it in.
A remix of the Swivel Wheelchair Cup Holder adapted so that it can hold regular mugs with a handle
The KWK D09 power chair has an armrest with a metal tube underneath so the original mounting method was not suitable. However this chair can have the controls fitted to either side so there is a spare hold at the end of the armrest with a…
Designed to fit the Cherry Tree office chair. https://www.amazon.co.uk/gp/product/B00K5SD3DS/ As the chair comes the back does not quite go up vertical and it can recline much further than most other office chairs. This adaptor extends…
This is a mount for the Gucee HD92 webcam which is designed to be used with the T-slot V-slot Universal camera mount system available at https://www.thingiverse.com/thing:2477180 Print Settings Printer Brand: Creality Printer: Ender 3…
This is a case to hold a HP server HSTNS-PD18 or HSTNS-PL18 power supply together with a custom PCB I designed to make the output available on Anderson Powerpole contacts. These are good power supplies for use with Amateur Radio as they…
An adapter to enable the Simplehuman food caddy to be hung over a cupboard door. The existing bracket is used so the bin can still be lifted off and the lid still held open magnetically. The download also contains a link to the design in…
I remixed the original to enlarge the opening to hold the toothbrush. Made a little wider as the toothbrush is slightly rounded. Added a square cutout at the back. Added a slight curve to the front to increase the slight added depth.
These are all currently available results.
