All models

Notebook laptop stand

A laptop stand for thinner notebooks. The v2 has a bit thicker bottom brace for thicker laptops. Category: 3D Printing

Vase mode wing with double wing spars (NACA 4412)

My attempt at the Tom Stanton VTOL wing. With two wing spars (16mm and 8mm) spaced 70mm from each other. Level with another at 0 deg of attack. Wing chord ~180mm Wing height ~23mm Ribs spaced 30mm apart.

Closet door latch

Small latches that screws into the door frame stop closet doors from swinging back open. Uses one M4 wood screw.

Visvalk VTOL

Disclaimer!! This project is currently mothballed, it has reached a point where I can only fix the problems with more money or talent, neither of which I currently have. I uploaded all the files for the design in step, iges, 3mf, obj, stl…

MOSFET mount

-Mount fort a Makerbase MKS MOS25 V1.1 -Middle hole for mounting screw Category: 3D Printers

Home assistant desk display (ESP32 v1 dev board + 2.42" OLED I2C + DHT22)

Snap fit for the screen and rear cover, M2 screws for the ESP32 board. Supports needed. Left and right side cable routing options. DHT22 → GPIO4 SDA → GPIO21 SCL → GPIO22

Vase mode wing - Single 16mm spar (NACA 4412)

The cutouts are for wire pass through for a upcoming project (as well as a locating hole for fixing the AOA) Chord: 180mm Spar: Center 58mm from the front Length: 250mm Thickness: 23.1mm

MKS Mosfet (MKS Mos25)

CAD files are not dimensionally accurate!!! (Sketch is accurate). Use merely for reference. Print Settings Printer: N\A Rafts: No Supports: No Category: 3D Printing

ESP32 Weatherstation

Parts: ESP32 Development board V1 Wave 1.54" Full Colour IPS Screen DHT11 sensor Some random screws (2x M3 for electronics, 2x Wood screws for back cover) Compares local readings from DHT11 sensor to API call from Openweathermap every 90…

Wrist watch stand

If you really don't know what this is we have a problem. If you have any suggestions just DM me.

FrSky Taranis Q X7 Travel Case

A case for transporting my radio to and from flight locations and storing it at home. It has a locking tab at the bottom and a Velcro strap (25mm wide) up top to keep the lid secured. Also has loops for a carrying strap (Up to 25mm wide).…

Ultimate frisbee disc clip

Locking frisbee clip (uses 4 M3x10 screws)

Home Assistant weather sensor (S2-MINI + BME280)

-ESP32 S2 mini -BME280: Cheap, small and accurate enough sensor for pressure, humidity, and temperature sensing -Small wood screw (OD: 4mm, Length: ~8mm)

Ding Ding with HOORAY

Tevo Tarantula X-axis rebuild

Base of the work from 'Ultimate TEVO TARANTULA upgrade' from kwijatkowski ( https://www.thingiverse.com/thing:2761136 ) but with a few alterations Category: 3D Printing

MGN12C Carriage

Remix for a MGN12C carriage Print Settings Printer Brand: TEVO Printer: Tarantula Rafts: No Supports: No Resolution: 0.2 Infill: 30% Filament: CRON PLA Black Category: 3D Printer Parts

Taranis Q X7 wall mount

A wall mount for a Taranis Q X7 stuck to the wall wit double sided tape

LM10UU bearing brace

Soft mount with zip ties for a LM10UU brace below a heated bed

Longboard wall clip

A bracket for storing a longboard on a skirting piece on a wall