Counting matching models…
GoPro Case for GoPro Hero 9, 10 and 11. Classic GoPro Mount. Print in TPU with supports. Not too tigh made on purpose. Several option are available under : - Normal - Split screen version - No Front Screen/Protected Front Screen Check…
GoPro type mount for the new Insta360 Go 2 Print in Flex Filament Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: 200 Infill: 100 Filament: ColorFabb Flex Black Category: Camera
Print in TPU with supports. If you want to use the version with the mount in TPU you probably need to remove the GoPro mount of the GoPro Mini and replace it with a plate availabe in 3D with the case. You need a torx T4 screwdriver to…
Slim GoPro Case for GoPro Hero 9, 10 and 11. Classic GoPro Mount. Print in TPU with supports. Not too tigh made on purpose. Check gcode file to find where put 3d support to print it. Post your makes! Other options are available here : -…
6S balance clip to prevent balance connector to move. it holds firmly attached to the lipo battery. Easy to print in TPU. Infill dont really matter the object is completly full because it mostly only perimeters. Post your makes! 4S…
TBS ND Filter holder for GoPro Hero 9, 10 and 11. Remix with thiner base. Nice to use with these cases : here Pay attention to the orientation of the filter before inserting it in the support (as the picture shows). Even if the lens of…
4S balance clip to prevent balance connector to move. it holds firmly attached to the lipo battery. Easy to print in TPU. Infill dont really matter the object is completly full because it mostly only perimeters. Post your makes! 6S…
Insert Organizer for official GoPro 9 / 10 Case. Remix : Added rounded edge from the original Post your makes!
AxisFlying Z25 Cineon DJI O3 Antenna Mount + Spacer. Standoff diameter is 3.2mm. Distance beetween standoff is 18mm.
Just a remix from VE2YTQ. It's the same case just a bit shorter and with the logo of park tool company. Post your makes!
FPV Motor Wire Protectors with Various Lengths Remix without zipties. I prefer using 3M textile tape. Post your makes!
GoPro 9 10 11 Base Fusion C220 F212 15°/ 20°/25° Degres Tilt Not too tigh made on purpose. Print in TPU. It's really close to props for the Low profile version of F212 or C220. Post your makes!
AxisFlying Z25 Camera mount. (Naked GoPro, Insta360Go, SMO 4K …) Perfect to put an Insta360 Go 2 with this type of mount : here ! You gonna need a M2x12mm bolt and a M2 nut.
Remix from fusion file. a bit stronger than the original. Category: R/C Vehicles
Mount for the new Insta360 Go 2 flywoo Explorer LR 4. Print the base in PETG and the mount in TPU. You gonna need a M2x12mm bolt and a M2 nut Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: Yes Resolution: 200…
Two type of mount for the new insta360 Go 2 and BetaFPX X95 V3. Print in Flex filament. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports: No Resolution: 200 Infill: 100 Filament: ColorFabb Flex Black Category: Camera
AxisFlying Z25 Cineon Camera Plate full
FPV Thrid person view mount for Insta360 GO2. Design is intended to bolt below the drone frame. Length between spacer is (25mm on the XL5 Titan Frame). Comment below if you want differents screw spacing for your specific frame) Hardware…
Remix from Dodox. Added extra design to put different size magnet : 10x3mm 8x3mm Ask your magnet size on comment section ! Post your makes!
It's a remix from Alexandr IDK (thingiverse) i just add a small hole to pass a lanyard and attached it to the checker. Post your makes!
Remix from fusion file without inferior part Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: Doesn't Matter Supports: No Resolution: 0.15 Infill: 100% Filament: Sainsmart TPU Black Category: R/C Vehicles
GoPro 11 Mini Base Fusion C220 F212 (15°/ 20°/25° Degres Tilt). Not too tigh made on purpose. Print in TPU. Post your makes!
Rear bottom bumper for Fusion C220 Frame.
These are all currently available results.
