Counting matching models…
I needed a GT2 belt clamp that could handle an outside loop, and couldn't find one, so I made this, which just slips over the side of the two belts placed back-to-back. I printed using PLA with 4 walls. Category: 3D Printer Accessories
Designed for 2022-2024 IONIQ 5. Flip horizontally in your slicer for the other side of the car. I put support blockers under the overhang, most modern printers should be able to handle printing the overhang without supports. I left the…
Here is a snap-together case for the FYSETC E4 board with the built-in antenna, since I couldn't find one. The top was designed to attach a 4010 fan on the outside. Also, take care when you're snapping the top on, as the tabs are a bit…
Easy to print, low profile hide-a-key box. No supports needed, but I would recommend using a deburring tool or sandpaper to trim around the edge of the lid, so it slides easily but is not too tight. STL files are designed for the 3mm x…
The plastic coating had worn off on the grabber teeth of the Quick Grips of my Thule Ascent cargo carrier, so I designed this TPU replacement, to prevent damage to the crossbars from the metal teeth. Print vertically, with the opening…
Simple 2" hitch cover design with tether. Print in TPU with at least 3 walls and 20% infill for stiffness. Print Settings Printer: BLV mgn Cube Rafts: No Supports: No Infill: 20% Filament: Inland TPU Category: Automotive
I made this reverse Bowden mount for my BLV mgn Cube, but it will attach to any 2020 extrusion with M3 screws and T-nuts. It's 8mm thick, so that you can screw in standard PC4-M6 fittings on top and bottom, and plug in my filament runout…
I built a DIY laser engraver around the Comgrow 10W laser module , and decided to design an air assist for it that replaces the existing laser shield. This should also fit the Comgrow Comgo Z1 module. This will work with a ~6mm air hose,…
Simple tray for under the armrest for a 2022+ Pathfinder. Print Settings Printer Brand: Creality Printer: Ender 3 Pro Supports: Yes Infill: 10 Filament: Inland PLA+ Category: Automotive
This is a bumper that is designed to be printed in TPU (I use Inland TPU) and attaches to the bumper bracket from https://www.thingiverse.com/thing:4306573 with m4x20mm screws, which I had left over from assembling the Tarmo4. I printed…
For this remix, I extended the neck of the original knob by 5mm, for a little extra clearance below the frame, and made the hole large enough for an M4 threaded insert. Category: 3D Printer Accessories
I wasn't satisfied with the other solutions for sunglasses storage for my IONIQ 5, so I made this variant, designed specifically around the larger measurements of my cheap sunglasses. This was designed to make it very easy to slip the…
This is my filament sensor remix for these switches from Amazon . I also enlarged the filament hole to fit a length of 4mm PFTE tube, which should give a very smooth filament path, and it plugs nicely into my reverse Bowden mount . Just…
Here's a way to mount 15mm corner light bar extrusions on top of a 3D printer. These are designed to attach to 2020 or 2040 extrusion with M3x8 screws and M3 T-nuts, and the photo is with them mounted on my BLV mgn Cube. Easiest to print…
This is a front LED mount, designed to work with the minimialistic BLV mgn Cube fan duct from https://www.thingiverse.com/thing:4149891 . Just use longer screws to mount in front of the hotend fan. Print Settings Printer Brand: Creality…
These are all currently available results.
