Counting matching models…
If you have a triple screen set up on your Sim Racing rig and want to lose the black strip that occurs where your screens meet then this is the basis of a DIY Bezel-Free Kit. The original ASUS ROG Bezel-Free Kit was an accessory that…
This is an outlet, inlet and electronics enclosure design the for SimHub Wind Simulator feature that allows to you to control fans via your racing simulation. You can implement effects like static wind or wind that changes with speed.…
This is a conversion for the Wind Ace Wind Simulation for Sim Hub that converts the back so it takes a 120mm fan. There is an adapter for the body so a fan can be fitted and then a rear flow guard for the back. I used the GDSTIME GDP1238…
SimHub provides many useful & cool features including a gear indicator. This is a great project for anyone getting started with SimHub and/or 3DPrinting. If you are building the bullet version make sure you insert the matrix before adding…
This is a LED Clip for the 1515 Extrusion found on the Voron Zero 0.1 Kit by Formbot. Although it is designed for the WS2818 5V RGB Led Strip it should fit something 10mm wide and 2mm deep. If n is the number of LEDs you are having per…
When I built my Voron Zero I was concerned at the ease at which someone could touch the mains voltage terminals on the PSU if the skirts (not supplied in the PiF kits) were missing. Additionally, the finger guard provided didn't feel…
Nobsound Amplifier Holder with a mount pattern that fits 8040 Bosch Rexroth compatible extrusion popular with Sim Racers. Will hold the amplifier in position bolted to the side of a sim racing rig or anything to be honest.
This is version 2 of my original Button Box that can be seen here . The key differences are: No 2 way switches. I didn't feel they were useful for simracing. Different Encoders that provide a stronger notch feel. But I also used Cherry MX…
This is a modular electronics case for 3d printers which I have used successfully for my Eryone Thinker (located underneath) and on the side of a Ender 5+ The attached model files provide the outer wall and any bases required. In addition…
These 3D printed covers secure and cover cables located into the slots of Bosch Rexroth 10mm Aluminium Extrusion. When located over cables especially thicker ones it can help to place the cable inside the cover before starting and/or…
3D Printable holding devices for hobby CNCs. Using the claw or a pair of beaks to set home X/Y with eggs to maintain the angle and then use cams to hold into position works really well for repeated jobs of the same type. Or just use them…
If you have Starlink internet you will be running a cable from Dishy to the location of your Starlink router. This is almost certainly from outside into your home and there is a good chance you will need to drill a reasonable sized hole…
Secures the cooling pipes and cable at the top of the Z.
Background During longer prints and/or operation of my Formbot Voron 0.1 I had many issues with hot end heat creep causing print failure. I started with a Dragon HF in the standard tool head before switching to the Bondtech LGX tool head.…
This is a Simhub Dash Unit that has the following front facing outputs/displays: 1 x HT16KK Single Colour Matrix: I used the Adafruit Small 1.2" 8x8 Ultra Bright Matrix which quite honestly is too bright. I think its set at around 4%…
Shim for aligning the Open Builds 8mm Acme Screw Block. Available in 3 sizes. I ultimately used 0.5mm
66mm Shim for an Open Builds Router Spindle Mount. Similar to those from Ooznest for the WorkBee but with a smaller lip and profiled trim at the back. Will also work for the Queen Bee and other variants. I printed in ABS but other…
Shim for fitting Heusinkveld Sprint Pedals to 8040 Extrusion. I printed this in normal PLA as a test and its still fine with no noise or flex. I have not felt the need to print it in carbon reinforced anything or ABS.
66mm Shim for an Ooznest Dust Shoe . Similar to those from Ooznest for the WorkBee but with a smaller lip. Will also work for the Queen Bee and other variants. I printed in ABS but other filaments should also be fine.
These are cure chamber parts for a enclosure built around the ELEGOO MARS PRO UV ARRAY WITH GRID ISSUE . Its a while since I built it and my memory of the parts is not 100% but the date stamps suggest the files are all correct and I have…
These two mounts allow you to attach Behringer EUROPOWER EPQ304 Amplifiers to be attached securely to 8020 extrusion popular with sim racers. I used them to secure the amplifier to my rig for the bass shakers. You can read more about my…
These are all currently available results.
