P
PrintablesTechAddict
Coin Holder
A coin tray designed for center console of car, but can be used anywhere needed.
- Downloads
- 951
- Likes
- 130
- Rating
- 5
All models
Counting matching models…
P
PrintablesTechAddict
18650/21700 Magnetic Battery Case
Print 2 of either model and glue 4 6mm x 3mm magnets using epoxy or superglue. Make sure magnets are in correct polarity before gluing or they will repel each other.
- Downloads
- 359
- Likes
- 66
- Rating
- 5
P
PrintablesTechAddict
Quest 2 wall mount
Wall mounts for Quest 2 headset, controllers and Link cable. Headset and controller mounts need supports.
- Downloads
- 240
- Likes
- 21
- Rating
- 1.5
P
PrintablesTechAddict
Adjustable LED Strip Light Bar
2 bars included. 1 is for 10mm wide LED strips and other is for 8mm LED strips. Can be scaled to any size in slicer. End Mount 40's can be mirrored for opposite ends. Use coupler to connect 2 bars. mounts can be mounted to V slot rails…
- Downloads
- 226
- Likes
- 50
- Rating
- 5
P
PrintablesTechAddict
Toothless Herb Grinder
A simple easy to print toothless grinder. Works great and easy to clean because “herbs” don't get stuck between any teeth.
- Downloads
- 132
- Likes
- 13
- Rating
- 0
P
PrintablesTechAddict
Rubbermaid Filament Roller Stand
This is designed to fit the Rubbermaid Takealongs Dry Food Container 21C. To save some print time it's also designed to use 3/4in PEX pipe for the roller. Cut the pipe to about 69mm and fit the end caps in. Uses 608ZZ Bearings.
- Downloads
- 116
- Likes
- 26
- Rating
- 5
P
PrintablesTechAddict
Playing Card Standing Case
Simple playing card holder with cover.
- Downloads
- 94
- Likes
- 9
- Rating
- 0
P
PrintablesTechAddict
Desktop USB Drive Holder
Desktop holder for SD and USB drives. One has 10 USB A slots, and other has 5 USB A and 5 USB C. Both have 5 MicroSD and 2 SD card slots. Can be printed upright for a layered top look or facedown for a glossy or textured top, depending on…
- Downloads
- 46
- Likes
- 7
- Rating
- 0
P
PrintablesTechAddict
Elite Series 2 Charging Dock
IMPORTANT - THE POLARITY OF THE MAGNETS HAS TO BE CORRECT FOR THE CHARGING DOCK. PLACE MAGNETS ON CHARGER FIRST THEN MARK THEM LIKE IN THE PICTURE, SO YOU GLUE THEM IN THE RIGHT POSITION. THE MAGNETS WILL REPEL EACH OTHER IF THIS IS…
- Downloads
- 44
- Likes
- 10
- Rating
- 5
P
PrintablesTechAddict
My K-Cup Filter Press
Flatten out any paper filter and center it on reusable filter. Push paper into filter using press until bottomed out. Cut excess paper off with scissors and fill with coffee. Cap fits snug over paper and filter. Brew and enjoy your…
- Downloads
- 34
- Likes
- 7
- Rating
- 5
P
PrintablesTechAddict
Magnetic Cable Hooks
Magnetic hook to hang cables to PC or any other metal surface. Uses 12mm x 3mm neodymium magnets. For heavier cables a small piece of electrical tape over face of magnet can keep it from sliding down surface.
- Downloads
- 18
- Likes
- 1
- Rating
- 0
P
PrintablesTechAddict
Oval Infinity Mirror w/Floating Eyes
Use white or transparent PLA so LEDs can shine through the thin layer in middle. (Things needed) 2 sheets of acrylic 280mm x 120mm. Mirror window film 3M 9448A adhesive tape LED Strip 10mm wide (Directions) 1) Cut acrylic to size and sand…
- Downloads
- 12
- Likes
- 2
- Rating
- 0
These are all currently available results.