Counting matching models…
I made this RC Plane stand so that i dont have to keep using the kitchen table, and i can work on it without bending over. There are three parts, but you will need to print several of each to complete it. I used 20x20mm aluminium tubing…
Updated to better spacing for holes and the switch. The Gasser engine is a RC Buggy engine , but in my case it is being used in a RC Helicopter. This therefore means that weight is everything, so this design is for a lighter weight cover,…
As a compliment to my other design, here is one that can be hung around the 5Litre container that Nitro fuel normally comes in. Category: R/C Vehicles
Here is the Zenoah Engine block and fan assembly, to complement the other parts i have. Category: R/C Vehicles
This is a compliment to the other part i have here on Thingiverse, so now you can complete the shroud around the flywheel in a lighter material, thus saving weight. I Have just updated this file. Category: R/C Vehicles
Ever had the Nitro engine drip all over your car, carpet after a run? then you need a stopper :-) Category: R/C Vehicles
For RC Helicopters every piece of weight saving is a good thing, so this design replaces a solid aluminium piece with a much lighter PLA model. Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: Yes…
To make it easier to see the settings of the needle valve on a Nitro engine, these indicators help in the extreme. Category: R/C Vehicles
As with anyone with an RC Buggy they will drive it to the limits, as i was no exception! So it was inevitable that i would break something, and that was this bolt that goes between the wheel and and drive shaft, it transfers the power to…
When you use a GAS engine in a RC Helicopter, the fuel tank is not pressurised but does need a vent to allow the fuel to flow. To help this happen a piece of tubing is added to the tank to vent it, however with Helicopters they are not…
After the original pushrod holder broke i designed a new one and added two of them to the Heli so it can reduce the vibration in the pushrod. Print Settings Printer: ANET A8 Rafts: No Supports: No Resolution: 200 Infill: 100 Filament:…
As part of my recycle of old RC Helicopter blades, they leave the ends exposed, and these can get wet, and thus out of balance, hence these covers that will close these ends and allow them to be waterproof. Category: Other
After bought a Gasser Model Helicopter i found that i did not have the right tool box, and so trying to fill ther model with Gas always was a problem, as the mechanical pump had no where to be stored. This is my solution to this problem,…
If you want to convert your Helicopter to Gas then you probably will use a Zenoah two stroke engine, and as these are quite heavy engines they need a suitable bracket. So although you can print this as PLA preferably a metal based…
Using a filter element for a RC petrol car you can use this assembly to make it a very light and compact air filter. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Yes Resolution: 200 Infill: 38 Filament:…
I took the design from "Daniel3Dprinter" ( https://www.thingiverse.com/thing:3750456 ) and spilt it into two parts for easy printing. Category: R/C Vehicles
Servo holder for Align TREX 700N Helicopters, as i could not find these online i decided to design and print my own, so for anyone else having the same trouble, please help yourself. Print Settings Rafts: No Supports: Yes Resolution: 200…
a battery tray holder for SAB Goblin helicopters Category: R/C Vehicles
This is a Header Tank holder for a squarish tank, but it can be modified for others too. Category: R/C Vehicles
I needed to balance a Nitro engine clutch and fan block for a helicopter. As this thing is rotating around 18,000 RPM it needs to be balanced, especially on a Helicopter. The Balancer i had was not big enough, and so when i saw a DU-Pro…
These are all currently available results.
