Counting matching models…
Уменьшение стука стола при Z-HOPE: фиксатор гаек ходовых винтов. Нужно два фиксатора на передние стойки (-SIDE) и один на заднюю (-BACK). You need two retainers for the front struts (-SIDE) and one for the rear strut.
Printed with PLA and 0.4 nozzle with 0.19 Layer height. Nail polish was used for the coloring. Smear the surface with petroleum jelly, pour the nail polish, and wipe off with a cotton disk. Mr_medvedko dushniak & diatel
A nice Bic lighter sleeve, that feels very tactile. It has holes to attach paracord and when the lighter is reversed, the sleeve protects the gas lever from accidental discharge. Used silk Black&Green PLA. Не удержался и напечатал еще…
Enlarged and redesigned Mini Bic J25 Lighter Sleeve v.2. Add some features
What can I say? Glue the two pieces together with glue and install!
Wall support to install this xiaomi router. Added some design features...
What can I say? Glue the cover and latch together with glue and install! For single-color printing, the model can be colored with acrylic markers. Unfortunately, I'm very bad at coloring... Much worse than modeling...
It looks best when printed with a silk duocolor PLA
Just a case with an on/off button and a wheel for adjustment
PLA-silk duocolor Supports Body and hands: layer height 0.17 Helmet 0.19
I ordered capsules with bubbles for levels and assembled them together. Diameter is 9.6 mm
Simple Case for the usb cable checker board.…
You'll need two M4x6x6 patch plates (bonks), two M4 screws and two washers. Main box printed with supports. Pla/petg. Estimated printing time is about of 4 hours. The probes holder can be attached on either the left or right side. The…
A simple paper towel holder design that resists unravelling when tearing away towels. Simplified and lightened.
Вручную добавил поддержек для верхней челюсти. Слой 0.23, 2 периметра, 3 верха-низа, инфилл ректилинеар 5% Пластик silk duo-color rose-black
Один из множества держателей детектора филамента. Спорный вариант, да. Нужно два винта и гайки М3. И один винт М4.
No supports, No brim, No rafts. Layer height: 0.25 Wall generator: Arachne Infill: 15% Grid Top/bottom layers: 3 Wall loops: 3 Orca 2.2.0. Print time: 27 min
This adapter came with my ASUS ROG GR8 II Use something other than PLA since the AC adapter gets pretty hot. I used PETG.
Чего уж тут описывать… Любой пластик и любой клей! Так как все баночки имеют чуть-чуть разные размеры, свою банку надо померять и отмасштабировать модель. Текущие размеры: диаметр верхней крышки: 27.2 мм диаметр нижней крышки: 26мм Смерть…
Cinema4D standart figure + any sculpting. Adjust all sizes and ratios to your taste. Need supports…
The built-in holder turned out to be inconvenient - the readings are not visible at this angle. Let's modify it...
The photo engravings show a pump from Gladiator, manufactured by Bravo. Nevertheless, it is also suitable for other pumps.
Для печати средней части "купола" лучше предусмотреть поддержки. Материал любой, слой 0.28, 3 периметра, 3 слоя сверху и снизу. Заполнение Grid 20%
Applicator body modified for Chinese syringes
The squares have a protrusion at the corner to make it easier to remove them from the table. Use layer height 0.2mm
Original model by https://mysku.club/profile/Omnicorn Internal bearing support added
The box and the insert are printed from what we have. And you can choose the maximum layer thickness! For the sealant, TPU is the best choice. But it doesn't have to be.
Wall maunt holder for ISKRA ERO 1050w angle grinder
Just a frame. Switch size 82.5x82.5mm
All the parts are assembled using glue. Also I used a permanent acrylic marker to outline it. FF-SNZB02-COVER – optional. Based on and in the style of this model https://www.printables.com/model/1433993-flashforge-adventurer-5m-air-locker
You will need a few drops of glue to assemble it. No supports.
Support is Desperately Needed
Target “switch” sizes: Height: 80mm Thickness: 5mm Corner radius: 10mm. Printing time 1 hour 20 min Weight 25 grams In slicer it is recommended to use “Varyable Layer Height” option.
Support for the pump to keep it upright for maximum fluid extraction
Laier height: 0.23 Wall loops: 3 Bottm/Top shells: 2 Supports: enable Arrange as shown in the screenshot. The second option (MONITOR HUB TOP MOUNT 5) is smoother, without unnecessary protrusions.
В принципе - все понятно из описания. Печатаем как есть. Внимательно проверяем настройки мостов. Вставляем сквозь палочки центральную планку, и заклеиваем торцы заглушками. Опционально. Можно и без них. Сверху паз для авторучки. Чтобы…
Обычно он во что-то вркуичвается шурупом с торца, но мне захотелось так. Пока что повесил на стенку.
The board is very small. It's even uncomfortable to hold in your hands. Especially when you're trying out the buttons, speakers, and other features. And there's a risk of short-circuiting the circuits on the junk on the table. Let's add…
Печатаем, смазываем внутренню поверхность клеем, вставляем старую крышку - готово. Petg
We’ll need a lot of support. A great deal of it. All the support we can get. 17g, 1h 20m, Petg
Берём любой пластик и печатаем. 2.5 грамма, 7 минут. Потребуется двухсторонний скотч.
Layer height 0.24mm, 3 walls, 20% infill Details: One piece print No supports required Uses all original hardware Assembly: Screw Original A1 Mini Spool holder adapter (Dark grey part with two screws) onto new 3d Printed mount. Use…
No supports. To indicate the size of the spool, simply color in the desired segments with a marker. The photos show the previous version of the case. This model features several improvements.
These are all currently available results.
