Counting matching models…
Please leave a like if you enjoyed the model or it helped you. :) Remixed from : https://www.thingiverse.com/thing:4715615 Started off by making it a bit easier to print by adding a slopes to some of the overhangs. Then ended up taking…
Simple under desk cable management hook. Designed to keep wires from being pulled out easily.. UDPATE 11-1-24: Added a version 2 file that has more rounded edges which are much safer when you bump into them. It's been thoroughly tested…
Added a spout to prevent all the soap water from just leaching under the soap dish and maybe to help it actually drip into the sink. The model's geometry was also reduced a bit to make it easier to work with inside of Fusion360 but it's…
This remix is intended to be printed and left on the V6 accessory. The V6 accessories snap into place and do not come off that easily. Additionally it does not require two pieces like the original. Made some other changed to clean up and…
Made some modification: tighten tolerances around hex nuts reduces bulk of back (to avoid back pressing on dog) made it easier to print (see image for recommended print orientation) tighter fit to my pup's Julius K9 harness. matched the…
These are the clips that hold the side panels in on the NCASE M1 and Lian Li PC-Q33 (and maybe other) cases. I've tried in ABS and it works well, so far it's went through a lot of cycles of me taking the panels on and off. Not sure if PLA…
Pretty simple stepper motor mount for 2020, has some adjustability by using the slotted screw holes. Can be used in a few different orientations. Motor screw hole slots are sized to M3. Probably a good idea to add washers. 2020 extrusion…
This is a spacer that goes between the wall and furniture. Originally designed it because I have blinds behind my couch so the couch can't sit flush against the wall. This spacer holds the couch in place so you sit in front of the couch…
Remix to support a 2 hole drag chain. Update: Seems like the original 3 hole and the 2 hole remix did not work. I made a new version that's been tested now and works well. I did desolder, flip, then resolder the hot end heater connectors…
Vertical stand for the Cloud Key G2
Helps to use the space in these bins a bit more effectively with smaller parts. 1, 2, 3, 4, 6, and 8-way bins, some can be mix and matched and used in one bin. Numbering marks in the bins are only to help with the order that these should…
My remix only changes the idler so that it only puts force on the bearings inner race and leaves a gap for the rest of the bearing to spin freely. I didn't change any other part of the design. Category: 3D Printer Parts
If this looks way too small in your slicer, please scale to from 100% to 2540%. [Updated] Went back and made a sleeker version. I've not gotten a chance to print and use it but there should not be any changed that affect functionality.…
If you want to drive the bottom fans by the video card, you'll need an adapter. something like this will work although there are other options. I'm only linking this one because you can clearly see the pinout order, in case you have a way…
Updated 12/19/2021 (details at bottom of this summary) DISCLAIMER: My printer has been heavily modified and there may be things that won't work on a stock CR-10 or Tevo Tornado. Please plan ahead make sure you cover all your bases. This…
Cover for the corner of sharp extrusions. Made this for a CR-10 because the original extrusion guard just kept slipping out. This was modeled for a 2020 to 2040 extrusion joint (based on the screw hole placements), may work on other…
This is vat stand for the Phrozen Sonic Mini. It's made around the dimensions of the aluminum vat but may fit the plastic one as well. The idea behind this was something a bit more safer for the fep film where you don't have to worry…
Use support enforcers to print, See the two pictures on orientation and what supports should look like. Requires heat set inserts.
My CR10 is a bit modified and the Z steppers have been pushed away a bit from the normal position. This guide allows a wider range of distances but also covers the stock location. Use the bearing (F688ZZ Flanged) and screws (countersunk…
These are just snap-in mounts for various accessories that can be held in place by a single M3 screw. It's designed for the screw to go in from the bottom. This snaps on nicely and is removable and adjustable. There are two versions, the…
Requires an M4 nut and bolt to clamp in place. Printing in ABS let me pry it open enough to put it on without removing the monitors and sliding down over the top. Not sure if other plastics will be able to do that without snapping. As a…
Double hook that fits Edsal shelving. Used the base from this spool mount because I liked the fit. https://www.thingiverse.com/thing:2757666 Updated: Added two new variations and modified to fit newer Edsal shelves that have smaller…
There is a recess on the bottom for 3M rubber feet (8-9mm diameter) on the bottom to keep it from sliding around on a desk.
Very simply mount, that will fit on onto an extrusion frame. Holes for mounting to 2020 extrusion are M5 sized. Holes for Duet board are m3. [Minor update 1]: I made a small mistake on the screw recess. Updated in v1.3.1. [ Update ]:…
Just a floating bearing guide for the top of a lead screw. Mount is 20mm wide to fit around 20 series extrusions. Requires a flanged bearing F688ZZ. Category: 3D Printing
Just a simple 2020 mounted nozzle storage that screws in securely by hand. I printed in ABS and it has a nice fit, other materials may need slight scaling. I recommend printing a portion as a test if not printing in ABS. Needs 2 x M3 8mm…
Designed this for my highly modified CR10 but can probably be used for any printer with a MGN12H rail. [update] Found a good fan setup that goes well with this. I suggest using this one. https://www.thingiverse.com/thing:3192682 I printed…
This mounts to the side PSU mount holes and allows you to have a fan in it's place when you move the PSU to towards the front mount. Needs M3 threaded inserts: I used these (m3x5x4):…
DISCLAIMER: BE EXTREMELY CAREFUL WHEN WORKING WITH MAINS VOLTAGE, I AM NOT RESPONSIBLE IF YOU GET HURT, INJURED OR DEAD! Simple candelabra male adapter to tap into female candelabra socket. Used this to adapt a philip hue bulb into my…
Just a cover to block the hole if you don't want to use the headphone cable. To avoid supports I made it into two pieces that locate into one another. A dab of super glue should do the trick to keep them together. Category: Computer
Using this on a Jet Bench grinder/belt sander to connect a Dyson vacuum. The internal diameter ranges from around 52.5mm to 53.4mm (tapered). Please measure it before printing. I had to scale this to about 100.7% when printing in ABS,…
I kept having my oem center caps stolen by someone in my neighborhood. I did not want to keep wasting my battery on sentry mode so I just switched to these. I think they still look good, and it's easier to remove the wheels. I ended up…
These are all currently available results.
